Honda GX160UT2 Manual page 33

62Z4H000.book 4 ページ ２０１１年５月２０日 金曜日 午前１０時５分
dummyhead dummyhead
SERVICE INFORMATION
Part
Carburetor Main jet
Pilot screw opening
Float height
Spark plug Gap
Spark plug cap Resistance (20°C/68°F)
Ignition coil Air gap
Primary resistance
Secondary resistance
Starter motor Brush length
Mica depth
Charge coil Resistance
Lamp coil Resistance
Reduction unit P.T.O. shaft journal O.D.
(Chain type:
P.T.O. shaft journal I.D.
without clutch)
(Crankcase cover)
Reduction unit Clutch friction disc thickness
(Chain type:
Clutch plate warpage
with clutch)
GX200
Part
Engine Maximum speed (at no load)
Idle speed
Cylinder compression
Cylinder head Warpage
Cylinder Sleeve I.D.
Piston Skirt O.D.
Piston-to-cylinder clearance
Piston pin bore I.D.
Piston pin Pin O.D.
Piston pin-to-piston pin bore
clearance
Piston rings Ring side clearance
Ring end gap
Ring width
Connecting Small end I.D.
rod
Big end side clearance
Big end I.D.
Big end oil clearance
Crankshaft Crankpin O.D.
Crankshaft runout
Cylinder barrel Camshaft journal I.D.
Crankcase Camshaft journal I.D.
cover
2-4
Item
BE54C A #70
BE54D A #68
BE66U A #68
BE54P A #70
BE54J B #68
BE54C A 2-1/4 turns out
BE54D A 1-7/8 turns out
BE66U A 1-7/8 turns out
BE54P A 2-1/2 turns out
BE54J B 1-7/8 turns out
13.7 (0.54)
0.70 – 0.80 (0.028 – 0.031)
7.5 – 12.5 kΩ
0.2 – 0.6 (0.01 – 0.02)
0.6 – 0.9 Ω
5.6 – 6.9 kΩ
11.0 (0.43)
1.6 (0.06)
1 A 3.15 – 3.85 Ω
7 A 0.22 - 0.30 Ω
12 V – 25 W 0.36 - 0.46 Ω
12 V – 50 W 0.18 - 0.23 Ω
19.929 – 19.950 (0.7846 – 0.7854)
20.000 – 20.021 (0.7874 – 0.7882)
3.5 (0.14)
Item
3,850 ± 150 min
1,400
0.35 MPa (3.6 kgf/cm
(rpm)
68.000 – 68.015 (2.6772 – 2.6778)
67.965 – 67.985 (2.6758 – 2.6766)
0.015 – 0.050 (0.0006 – 0.0020)
18.002 – 18.008 (0.7087 – 0.7090)
17.994 – 18.000 (0.7084 – 0.7087)
0.002 – 0.014 (0.0001 – 0.0006)
Top 0.035 – 0.070 (0.0014 – 0.0028)
Second 0.045 – 0.080 (0.0018 – 0.0032)
Top 0.200 – 0.350 (0.0079 – 0.0138)
Second 0.350 – 0.500 (0.0138 – 0.0197)
Oil (side rail) 0.2 – 0.7 (0.01 – 0.03)
Top 0.950 – 0.970 (0.0374 – 0.0382)
Second 0.940 – 0.960 (0.0370 – 0.0378)
18.005 – 18.020 (0.7089 – 0.7094)
0.1 – 0.7 (0.004 – 0.028)
30.020 – 30.033 (1.1819 – 1.1824)
0.040 – 0.063 (0.0016 – 0.0025)
29.970 – 29.980 (1.1799 – 1.1803)
14.000 – 14.018 (0.5512 – 0.5519)
14.000 – 14.018 (0.5512 – 0.5519)
Standard
–
Standard
-1 (rpm)
+ 200
min -1 (rpm)
– 150
2 , 51 psi)/600 min -1
–
–
Service limit
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
6.0 (0.24)
1.1 (0.04)
–
–
–
–
–
–
3.0 (0.12)
0.10 (0.004)
Unit: mm (in)
Service limit
–
–
–
0.10 (0.004)
68.165 (2.6837)
67.845 (2.6711)
0.12 (0.005)
18.048 (0.7105)
17.954 (0.7068)
0.08 (0.003)
0.15 (0.006)
0.15 (0.006)
1.0 (0.04)
1.0 (0.04)
1.0 (0.04)
0.93 (0.037)
0.92 (0.036)
18.07 (0.711)
1.1 (0.04)
30.066 (1.1837)
0.12 (0.005)
29.92 (1.178)
0.10 (0.004)
14.048 (0.5531)
14.048 (0.5531)