Table of Contents
Advertisement
Procedure for copying to a virtual track
Here's how virtual track "a" (=currently selected) of
track 1 can be copied to virtual track "b" of track 1.
1. Verify the copy destination.
In the [TRACK] "Vtr1–8" tab page, make sure that
track 1 virtual track "b" is blank or is a track that may
be erased (overwritten). After you verify this, you
must return the setting to "a."
2. Select the Copy Whole command.
In the [TRACK] "EditTrk" tab page, set "EditType" to
"CopyWholeTrack."
3. Select the copy source track number.
Set "SourceTrack" to track 1.
4. Select the copy destination track number.
Set "DestTrack" to track 1.
5. Select the copy destination virtual track.
Set "DestVTrack" to virtual track "b."
6. Execute the editing command.
Press the "Exec." button.
The display will ask "AreYouSure?," so press the
"Yes" button to execute the command.
When processing is completed, the display will
indicate "Completed." Press the "OK" button.
7. In the [TRACK] "Vtr1–8" tab page, select virtual
track "b" for track 1.
8. Verify that the data was copied correctly.
Play back from the beginning of the song, and verify
that the data was copied correctly.
You can use Undo to return to the state before execut-
ing the command.
In this case, you must return track 1 to virtual track
"a."
Exchanging entire tracks/virtual tracks:
Swap Whole Track
This command exchanges (swaps) the data of an entire
recorded track (from beginning to end) with the data of
another entire track.
• Not only individual tracks, but multiple tracks can be
swapped simultaneously.
This command can be used in ways such as the follow-
ing.
• Recorded tracks can have their numbers re-ordered by
type.
• Data that is scattered across different virtual tracks can
be rearranged into virtual track "a" etc.
Procedure for exchanging an entire track
Here's how track 1 can be exchanged with the currently
selected virtual track "a" of track 2.
1. Select the Swap Whole command.
In the [TRACK] "EditTrk" tab page, set "EditType" to
"SwapWholeTrack."
SourceTrack
DestTrack DestVTrack
2. Select the swap source track number.
Set "SourceTrack" to track 1.
3. Select the swap destination track number.
Set "DestTrack" to track 2.
4. Select the swap destination virtual track.
Set "DestVTrack" to virtual track "a."
5. Execute the editing command.
Press the "Exec." button.
The display will ask "AreYouSure?," so press the
"Yes" button to execute the command.
When processing is completed, the display will
indicate "Completed." Press the "OK" button.
6. Verify that the data was exchanged correctly.
Play back from the beginning of the song, and verify
that the data was exchanged correctly.
You can use Undo to return to the state before execut-
ing the command.
Procedure for exchanging with a virtual track
Here's how currently selected virtual track "a" of track 1
can be exchanged with virtual track "b" of track 1.
1. Verify the copy destination.
In the [TRACK] "Vtr1–8" tab page, make sure that
track 1 virtual track "b" is the track that you wish to
exchange. After you verify this, you must return the
setting to "a."
2. Select the Swap Whole command.
In the [TRACK] "EditTrk" tab page, set "EditType" to
"SwapWholeTrack."
3. Select the swap source track number.
Set "SourceTrack" to track 1.
4. Select the swap destination track number.
Set "DestTrack" to track 1.
67
Advertisement
Table of Contents
