Download
Share
Print this page
Juniper QFX5200-32C-L Quick Start Manual
  1. Manuals
  2. Brands
  3. Juniper Manuals
  4. Switch
  5. QFX5200-32C-L
  6. Quick start manual
Juniper QFX5200-32C-L Quick Start Manual

Juniper QFX5200-32C-L Quick Start Manual

Hide thumbs Also See for QFX5200-32C-L:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Quick Start Guide
QFX5200-32C and QFX5200-32C-L Quick Start Guide
IN THIS GUIDE

System Overview

The Juniper Networks QFX5200-32C and QFX5200-32C-L are compact 1 U standalone Ethernet switches that provides
a line rate configuration packet performance, very low latency, and a rich set of Layer 3 features. The routing engine and
control plane are driven by the 1.8 Ghz quad-core Intel CPU with 16 GB of memory and two 32 GB solid-state drives
(SSD) for storage.
The QFX5200-32C and QFX5200-32C-L comes standard with redundant fans and redundant power supplies. Switches
can be ordered with either ports-to-FRUs or FRUs-to-ports airflow. The QFX5200-32C is available with AC or DC power
supplies; the QFX5200-32C-L is available only with AC power supplies.
The QFX5200-32C models run standard Junos Operating System (OS) and is supported as a standalone switch, (Junos
OS Release 15.1X53-D30 and later), a member in a QFX5200-32C Virtual Chassis (Junos OS Release 17.3R2 and later,
or as a; satellite device in a Junos Fusion Provider Edge system (Junos OS Release 18.1R1and later). The QFX5200-32C-L
models run Junos OS Evolved and is supported as a standalone switch (Junos OS Evolved Release 18.3R1 and later).

Advertisement

loading

Related Manuals for Juniper QFX5200-32C-L

Summary of Contents for Juniper QFX5200-32C-L

  • Page 1: Table Of Contents

    OS Release 15.1X53-D30 and later), a member in a QFX5200-32C Virtual Chassis (Junos OS Release 17.3R2 and later, or as a; satellite device in a Junos Fusion Provider Edge system (Junos OS Release 18.1R1and later). The QFX5200-32C-L models run Junos OS Evolved and is supported as a standalone switch (Junos OS Evolved Release 18.3R1 and later).

  • Page 2: Tools And Parts Required For Installation

    Register product serial numbers on the Juniper Networks website and update the installation base data if there is any addition or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable for not meeting the hardware replacement service-level agreement for products that do not have registered serial numbers or accurate installation base data.

  • Page 3: Part 1, Mounting The Switch Into A 4 Post Rack

    Part 1, Mounting the Switch into a 4 Post Rack The QFX5200-32C and QFX5200-32C-L can only be mounted in a four-post rack configuration. To mount the device in a 19-inch rack: 1. Attach the ESD grounding strap to your bare wrist and to a site ESD point...
  • Page 4 Figure 2: Attach Chassis to Rack 8. Continue to support the switch while sliding the rear mounting-blades into the channel of the side mounting-rails and securing the blades to the rack. Use the four mounting screws (and cage nuts and washers if your rack requires them) to attach each blade to the rack.

  • Page 5: Part Ii. Ground The Chassis And Connect Power

    Connect Power to the Switch The QFX5200-32C and QFX5200-32C-L ships with two factory-installed power supplies. The QFX5200-32C-CHAS is a chassis spare and is shipped without power supplies or fans. To connect power to an AC-powered chassis: 1.

  • Page 6: Part Iii. Connect The Qfx5200-32C Or Qfx5200-32C-L To The Nework And Perform Initial Configuration

    5. If the AC power source outlet has a power switch, set it to the ON (|) position. 6. Verify that the AC LEDs are lit green and on steadily. Part III. Connect the QFX5200-32C or QFX5200-32C-L to the Nework and Perform Initial Configuration You must perform the initial configuration of the switch through the console port using the CLI or through Zero Touch Provisioning (ZTP).
  • Page 7 NOTE: On the QFX5200-32C and QFX5200-32C-L, management ports em0 (labeled C0) and em1 (labeled C1) are found on the FRU end of the switch. 9. (Optional) Configure the static routes to remote prefixes with access to the management port.

  • Page 8: Qfx5200-32C And Qfx5200-32C-L Safety Warning Summary

    The QFX5200-32C and QFX5200-32C-L weighs approximately 23.5 lb (10.66 kg). Manually installing the QFX5200-32C and QFX5200-32C-L in a rack or cabinet at a height above 60 in. (152.4 cm) requires two people to lift the switch and install mounting screws. To prevent injury, keep your back straight and lift with your legs, not your back.
  • Page 9 The attached power cable is only for this product. Do not use the cable for another product. In the event of a hardware failure, please contact Juniper Networks, Inc. to obtain a Return Material Authorization (RMA) number. This number is used to track the returned material at the factory and to return repaired or new components to the customer as needed.

This manual is also suitable for:

Qfx5200-32c