Monessen Hearth NB18 Installation And Operating Instructions Manual page 39

NB18/NB24 Gas Log Set
1. Press the ON/up button to turn on
the fireplace. The flame icon on
the LCD displays High.
2. Press the OFF/down button to de-
crease the flame height and turn
off the fireplace. When the OFF/
down button is pressed for three
times, the flame icon changes
form High to Medium, to Low, then
to Off.
3. If the OFF button is held for more
than 3 seconds at any flame
height, the fireplace will be turned
off and the flame icon disappears.
4. Sliding up and down on the arrow buttons can also
turn on or turn off the fireplace.
5. If the fireplace is shut off using the above methods in 3
and 4, all the settings will be remembered and will be
resumed next time the fireplace is turned on (Memory
Off).
Timer Mode
Figure 61
Press the TIMER button to enter timer
mode. The fireplace will stay on for a
period of time as specified by the tim-
er and then be shut off by the trans-
mitter when the timer counts down to
zero.
1. When the TIMER
pressed, Set Time appears in the
frame of the button and flashes.
2. Use ON and OFF arrows to in-
crease or decrease the Set Time
in 15 min. increments, between 0:00 to 6:00. Sliding
up and down on the arrow buttons will increase or de-
crease the Set Time in 1 hour increments.
3. Push the TIMER button again to confirm the Set Time,
the transmitter sends an ON signal to turn on the fire-
place.
4. The flashing stops and the ON/up and OFF/down but-
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
5. The TIMER button can be used when the transmitter
is in Manual Mode or in Thermostat Mode. In both
modes, the fireplace will be shut down completely
when the timer counts down to zero.
6. To exit Timer Mode,
a. Push and hold the TIMER button for 3 seconds Or
b. Use the OFF/down buttons to decrease the Set
Time to zero Or
c. Slide down on the arrow buttons to exit TIMER
mode and shut off the fireplace.
Monessen • NB18/24 Gas Log Set Installation/Owner's Manual • 81D0107 • Rev I • 01/19
TOUCH SCREEN REMOTE CONTROL OPERATION — SCR MODELS
Figure 60
FP2662
manual mode
button is
Figure 61
FP2663
timer mode
Thermostat Mode
Figure 62
Press the THERMO button to set the
transmitter in thermostat mode. The
transmitter will automatically turn on
the fireplace when the room tem-
perature is below the set tempera-
ture and turn off the appliance when
the room temperature is above the
set temperature within one degree.
1. When the THERMO button is
pressed, the Set temperature ap-
pears in the frame of the button
and flashes.
2. Use ON and OFF to increase or decrease the Set
temperature in 1 degree increments, between 45 de-
grees and 90 degrees. Sliding up and down on the
arrow buttons will increase or decrease the Set Tem-
perature in 10 degree increments.
3. Press the THERMO button again to confirm the Set
Temperature. The transmitter will send out an On
signal or an Off signal depending on the relationship
between the Set temperature and the Room tempera-
ture.
4. The flashing stops and the ON and OFF buttons be-
come flame controller again.
5. To exit Thermostat Mode and shut off the fireplace:
a. push and hold the THERMO button for 3 seconds
Or
b. press the OFF button three times Or
b. slide down on the arrow buttons.
Smart Mode Option for Thermostat Mode
Figure 63
Press and hold the THERMO button and the ON/UP but-
ton at the same time for 3 seconds to toggle between
Smart Mode thermostat and the
regular Thermostat Mode. The
icon "Smart Mode" will appear
under the Set Temperature.
The transmitter will automat-
ically adjust the flame height
according to the difference be-
tween the Set temperature and
the Room temperature. There
is no manual flame height ad-
justment.
NOTE: there will a 10 second
delay for the flame adjustment
when the fireplace is turned on.
1. When Set Temp. is 3° F or higher than Room Temp.,
flame height will be on High.
2. When Set Temp. is 2° F higher than Room Temp.,
flame height will be on Medium.
Figure 62
FP2664
thermo mode
Smart
Mode
Icon
Figure 63
FP2665
smart mode
39