Page 1
Entry Model: MC502S On /Off Transfer Compatible Rinnai water heater models: Thi s manual applie s to th e Rinnai Wireless Controller MC502S. Infinity XR 32 Infinity XR 26 Infinity XR 24 This manual must be used in conjunction with the...
HOW TO USE WIRELESS CONTROLLERS ................3 TURNING ON THE WIRELESS CONTROLLER................3 ADJUSTING TEMPERATURE ..................... 3 TRANSFERRING PRIORITY BETWEEN CONTROLLERS............4 WIRELESS CONTROLLERS BATTERIES .................. 4 TROUBLESHOOTING....................5 ERROR CODES ........................... 5 SERVICE ............................5 INSTALLATION MANUAL ..................6 CONTACT INFORMATION ..................16 Rinnai New Zealand Operation Manual...
Rinnai wireless controllers must not be used in the vicinity of other devices if radio interference with such devices could result in a dangerous situation, unless it is verified that interference will not occur.
Suggested temperatures are: Kitchen 50°C ~ 55°C*, Shower 37°C ~ 43°C * Temperature may not be available on all installations. Rinnai water heaters can be programmed to deliver higher temperatures via the kitchen controller. Contact Rinnai for more details. These temperatures are suggestions only. You may find higher or lower temperatures more comfortable.
A parent or carer should always check the temperature before a child is placed in CAUTION contact with hot water, see page 1. Whilst hot water outlets are open the set temperature may be lowered. However it cannot then be raised above 43°C. This is a safety feature. NOTE Rinnai New Zealand Operation Manual...
Use only 4 x 1.5V AA ALKALINE batteries. NEVER mix old and new batteries. Battery life is approximately 1 year. IMPORTANT Remove batteries if the remote control is not going to be used for a long period. This will help avoid damage from leaking batteries. Rinnai New Zealand Operation Manual...
Rinnai has a Service and Spare Parts network with personnel who are fully trained and equipped to give the best service on your Rinnai appliance. If your appliance requires service, please call 0800 Rinnai (0800 746 624).
INSTALLATION MANUAL INSTALLATION GENERAL ..................7 RINNAI WIRELESS CONTROLLERS ....................7 GENERAL INSTALLATION INFORMATION ..................7 POSITIONING OF TRANSCEIVER AND WIRELESS CONTROLLERS ..........8 COMMUNICATION CABLE ..................9 CONNECTING COMMUNICATION CABLES TO THE WATER HEATER ......... 9 TRANSCEIVER INSTALLATION ................10 MOUNTING THE TRANSCEIVER ....................10 CONNECTING COMMUNICATION CABLE TO THE WIRELESS TRANSCEIVER ......
New Zealand. GENERAL INSTALLATION INFORMATION Rinnai Wireless Transceivers can be connected to the water heater models listed on the cover page by the end user in accordance with these Instructions. These water heaters contain the ’Ezi connect’ cable connector and a qualified tradesperson is not required.
The transceiver may be mounted inside metal recess boxes or pipe covers, however this may also reduce signal strength. Take the signal strength into consideration when determinig the location for the wireless water controllers. Rinnai New Zealand Operation Manual...
‘Quick connect’ cable connector at the water heater. Extension cables are available from Rinnai. Alternatively, two core sheathed (double insulated) flex with minimum cross sectional area of 0.5mm² may be used. Cable lengths must not exceed 20 metres.
2. Set the transceiver’s maximum water temperature to 55°C by pressing the ‘Max Temp’ button until 55 is displayed. Refer to “Master and Sub controllers and temperatures” on page 7 for information regarding using of the maximum temperatures with wireless water controllers. NOTE Rinnai New Zealand Operation Manual...
On / Off Transfer On / Off Transfer Press once to start the tuning process approximately On / Off Transfer On / Off Transfer On / Off Transfer 5 seconds Press once On / Off Transfer Rinnai New Zealand Operation Manual...
MC91 (not programmed as a Master Controller) will be assigned to Channels No. 2 and/or No.1 and/or No. 3. Install the wireless controllers to any of the unassigned channels following steps 1 to 9 on page 11. Rinnai New Zealand Operation Manual...
5. Slide the wireless controller back into its’ wall mounting bracket. ADDITIONAL WATER CONTROLLER MOUNTING CONSIDERATIONS. The MC502S uses a Liquid Crystal Display (LCD) for the digital NOTE monitor. Light reflections can make the LCD difficult to see at direct eye level.
Page 16
NOTES Rinnai New Zealand Operation Manual...
CONTACT INFORMATION Rinnai NZ Ltd. PO Box 24068 Royal Oak Auckland New Zealand 0800 Rinnai (0800 746 624) www.rinnai.co.nz info@rinnai.co.nz U284-0172 U284-0172 Printed in Japan YYYY.MM...