Dimplex DLX Series Important Instructions

Convector
DLX Series

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock
and injury to person, including the following:
1. Read all instructions before using this heater.
2. Do not operate any heater after it malfunctions. Discon-
nect power at the service panel and have the heater
inspected by a reputable electrician before reusing.
3. To disconnect the heater, turn the controls to the OFF
position, and turn off the power to the heater circuit at the
main disconnect panel.
4. Do not insert or allow foreign objects to enter any ventila-
tion or exhaust opening, as this may cause an electric
shock or fire, or damage the heater.
5. To prevent a possible fire, do not block the air intakes or
exhaust in any manner.
6. A heater has hot and arcing or sparking parts inside. Do
not use it in areas where gasoline, paint, or flammable
vapors or liquids are used or stored.
7. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.
8. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materi-
als, such as furniture, pillows, bedding, papers, clothes,
etc. and curtains at least 3 ft. (0.9 m) from the front and
sides of the heater.
9. Extreme caution is necessary when any heater is used
by or near children or invalids, and whenever the heater
is left operating and unattended.
10. Do not use outdoors.
11. Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.

SAVE THESE INSTRUCTIONS

Installation Instructions

WARNING: Do not install the heater where the controls
can be reached by a person bathing or showering.
CAUTION: The heater must not be located directly be-
neath a wall socket outlet.
CAUTION: The supplied hanging components are de-
signed for use with this heater only. Improper use, or use
for purposes other than intended, may cause damage or
injury.
1. Remove the mounting bracket from the back of the con-
vector.
Figure 1
5.9"
(150 mm)
MIN
4.6"
A
(118 mm)
10"
(255 mm)
MIN
Model
DLX0500
DLX1000
DLX1500
DLX2000
2. Using the mounting bracket as a guide determine the lo-
cation of the convector, see Figure 1 for minimum clear-
ances.
3. Attach the mounting bracket securely to the wall using
the appropriate hardware (not included) for the mounting
surface.
4. Mount the convector to the mounting bracket.
!
NOTE: Ensure that the air can enter and leave the heater
freely, through the inlets at the bottom and the outlets at the
top.
Electrical Connection
WARNING: All wiring must comply with National Electrical
codes and local codes and utility requirements. This in-
stallation should be entrusted to duly qualified personnel
where required by law.
Connect the supply wire into a properly rated recess box.
!
NOTE: Consult your local electrical code for applicable
wire gauge.
Connect L1 from the power supply to the L1 labelled wire
from the unit, connect the L2 wire from the power supply to
the L2 labelled wire from the unit, and connect the ground to
the ground screw on the unit.
Wiring Diagram
Thermal Cutout
5.9"
(150 mm)
MIN
16.9"
(430 mm)
16.9"
(430 mm)
7.25"
(184mm)
4.1"
(105 mm) 5.9"
2.5"
(150 mm)
(64 mm)
MIN
A
4.6 in. (116 mm)
11.2 in. (285 mm)
14.0 in. (356 mm)
20.7 in. (526 mm)
L1
L2
Ground
7212820100R02