Specifications - Sony SRX-R110 Brochure & Specs

Specifications

SXRD Device Main Specifications
Display device SXRD (Silicon X-tal Reflective Display)
Size 1.55" across Diagonal
Resolution 4096(H) X 2160(V) Pixels
Reflectivity 72%
Contrast (as device) More than 4000 : 1
Pixel pitch 8.5µm
Width (between pixels) 0.35µm
Response speed 5msec (tr + tf)
Liquid crystal mode Vertical Aligned Mode
Alignment layer Inorganic Thin Film
Backplane process 0.35µm MOS Process
Liquid crystal cell gap Less than 2µm
Optical
Projection system 3-SXRD panel, prism color integrated system
Imaging device SXRD, 1.55-inch (diagonal), 4096(H) x 2160(V) pixels
on each chip
Lamp 2kW Xenon lamp x 2 (SRX-R110)
1kW Xenon lamp x 2 (SRX-R105)
Screen coverage 14 feet to 51 feet (Approx. 4.5 m to 15.5 m)
(viewable area, measured horizontally)
Light output 10,000 ANSI lumens ±10% (SRX-R110)*
5,000 ANSI lumens ±10% (SRX-R105)
General
White reference Xenon white reference
Contrast more than 1800:1
Resolution 600 TV lines (SDI input/SMPTE-259M)
1920 x 1080 pixels (HD-SDI input, SMPTE-292M)
4096 x 2160 pixels (RGB)
Signal specifications Video: Component (Y
Computer: XGA, SXGA, UXGA
Power requirements AC 200 to 240 V, 50/60 Hz (SRX-R110)
AC 100 to 240 V, 50/60 Hz (SRX-R105)
Operating temperature +5ºC to +35ºC (+41ºF to +90ºF)
Storage temperature -20ºC to +60ºC (12ºF to +140ºF)
Operating humidity 35% to 85% (without condensation)
Storage humidity 10% to 90%
Dimensions Approx. 740 x 500 x 1330mm
(W x H x D) (29 4/5 x 19 4/5 x 52 3/5 inchs)
Mass Approx. 110 kg (242 lb 8oz)
Input/Output
Input A
Open for optional signal interface board
Input B
Open for optional signal interface board
Input C
Open for optional signal interface board
Input D
Open for optional signal interface board
Remote interface
D-sub 9-pin, RS-232C (female) x 1
Ethernet terminal, 10Base-T/100Base-TX x 1
ANSI lumens is a measuring method of the American National Standards Institute.
*
Preset Data of Input Signals
No Signal Number fH
0 NO INPUT 0
3 VIDEO60(480_60I) 15.73 kHz
4 VIDEO50(575_50I) 15.63 kHz
5 HDTV(1080_60I) 33.75 kHz
23 1024 x 768_VESA60 48.36 kHz
24 1024 x 768_VESA70 56.48 kHz
25 1024 x 768_VESA75 60.02 kHz
26 1024 x 768_VESA85 68.68 kHz
32 1280 x 960_VESA60 60.00 kHz
33 1280 x 960_VESA75 75.00 kHz
36 1280 x 1024_VESA60 63.97 kHz
37 11280 x 1024_VESA75 79.98 kHz
X
White reference 0.3140
Cb Cr), HD (G B R/Y
• • • •
fV Aspect Horizontal
Sampling
0
59.94 kHz 4:3 1280
50.00 kHz 4:3 1280
60.00 kHz 16:9 1920
60.00 kHz 4:3 1024
70.07 kHz 4:3 1024
75.03 kHz 4:3 1024
85.00 kHz 4:3 1024
60.00 kHz 4:3 1280
75.00 kHz 4:3 1280
60.01 kHz 5:4 1280
75.03 kHz 5:4 1280
Input Boards
LKRI-001
Analog input board
LKRI-002
HD-SDI (4:2:2)
input board
LKRI-003
Y
Dual-link HD-SDI
0.3510
input board
Others
Safety regulations
Pb Pr)
• •
Supplied
accessories
Optional
accessories
Vertical No Signal Name
Sampling
38 1280 x 1024_VESA85
480 39 1600 x 1200_VESA60
570 45 1080_50I
1080 47 720_60P
768 48 720_50P
768 49 1080_48I (24PsF)
768 (75) 1080_60i
768 (76) 1080_25PsF
960 (77) 1080_30PsF
960
Note: When a signal other than the preset signals shown above is fed into this projector, the images may not
*
be projected properly.
1024
SXGA+(1400 x 1050) computer signal is not supported by this projector. If this signal is fed into the
*
1024
projector, one of the four directions of an image are irregularly missing.
BNC x 5, HD/SD analog video input,
RGB/Y Cb Cr selectable
• •
Computer signals
R 0.7 Vp-p ±2dB positive, 75 Ω
G 0.7 Vp-p ±2dB positive, 75 Ω
B 0.7 Vp-p ±2dB positive, 75 Ω
Standard definition video [Y Cb Cr]
• •
Y 1.0 Vp-p ±2dB sync negative, 75 Ω
Cb 0.7 Vp-p ±2dB positive, 75 Ω
Cr 0.7 Vp-p ±2dB positive, 75 Ω
High definition video [RGB]
R 0.7 Vp-p ±2dB positive, 75 Ω
G with sync 1.0 Vp-p ±2dB, 75 Ω, Tri-level sync:
±0.3 Vp-p / Bi-level sync: 0.3 Vp-p
B 0.7 Vp-p ±2dB positive, 75 Ω
High definition video [Y Pb Pr]
• •
Y 1.0 Vp-p ±2dB, 75 Ω,Tri-level sync:
±0.3 Vp-p / Bi-level sync: 0.3 Vp-p
Pb ±0.35 Vp-p ±2dB, positive 75 Ω
Pr ±0.35 Vp-p ±2dB, positive 75 Ω
Sync
HD Horizontal TTL level, high impedance, sync
positive/negative
HD Vertical TTL level, high impedance, sync
positive/negative
BNC x 2(Input x 1,Loop-through out x 1)
HD-SDI (SMPTE-292M / ITU-R.BT709 / BTA-S004)
SDI (SMPTE-259M / ITU-R.BT601)
BNC x 4(Input x 2,Loop-through out x 2)
HD-SDI (Single-link, HD-SDI/4:2:2,SMPTE-292M):Y
DC-SDI (Single-link, DC-SDI/4:2:2):Y Pb
• •
Dual-link HD-SDI (Dual-link HD-SDI/4:4:4,SMPTE-372M):RGB,
Dual-link DC-SDI (Dual-link DC-SDI/4:4:4):RGB
[UL60950 listed], [cUL60950], [FCC Class A], [IC Class A], [VCCI
Class A], [EN60950],[CE Class A], [C-tick], [GB4943], [GB9254],
[K60950], [CISPR22], [CISPR24]
Remote controller x 1/ CD-ROM x 1 (Remote control application
for Windows XP Professional Edition) / Dry cell (AA size) x 2 /
®
Ethernet Cross Cable (3 m) x 1
Operation instructions x 1 / Installation manual x 1
LKRL-Z115: 1.5 to 1.9x zoom lens
LKRL-Z120: 1.9 to 2.3x zoom lens
LKRL-Z125: 2.3 to 4.0x zoom lens
LKRL-Z140: 4.0 to 7.0x zoom lens
LKRI-001: Analog input board
LKRI-002: HD-SDI (4:2:2) input board
LKRI-003: Dual-link HD-SDI input board
LKRX-105: 1kW Xenon lamp bulb for replacement (for SRX-R105)
LKRX-B105: 1kW Xenon lamp house unit for replacement (for SRX-R105)
LKRX-110: 2kW Xenon lamp bulb for replacement (for SRX-R110)
LKRX-B110: 2kW Xenon lamp house unit for replacement (for SRX-R110)
LKRA-001: 8-inch Exhaust Duct adaptor
fH fV Aspect
91.15 kHz 85.02 kHz 5:4
75.00 kHz 60.00 kHz 4:3
31.25 kHz 50.00 kHz 16:9
45.00 kHz 60.00 kHz 16:9
37.50 kHz 50.00 kHz 16:9
27.00 kHz 48.00 kHz 16:9
33.75 kHz 60.00 kHz 16:9
31.25 kHz 50.00 kHz 16:9
33.75 kHz 60.00 kHz 16:9
Pb Pr,
• •
Pr,
Horizontal Vertical
Sampling Sampling
1280 1024
1600 1200
1920 1080
1280 720
1280 720
1920 1080
1920 1080
1920 1080
1920 1080
11