Scion Instruments 436-GC Service Manual page 68

436-GC/456-GC
Code Error Description
372 Sampler Communication error
373 Sampler Tower error
374 Sampler Carrousel error
375 Sampler Syringe Sled error
376 Sampler Plunger error
377 Sampler Syringe Missing
378 Sampler Vail Missing
379 Sampler Dual Dup Mode Delay Expired
380 Sampler Run not started after Inj
381 Sampler Syringe volume exceeded
383 Sampler Tower sensor not found
384 Sampler Carrousel sensor not found
385 Sampler Syringe sled sensor not found
386 Sampler Plunger sensor not found
387 Sampler Plunger Strokes exceed limit
Gas saver timeout expired (position)
388 Front Gas saver timeout exceeded
389 Middle saver timeout exceeded
390 Rear saver timeout exceeded
391 Run ended before second injection
Miscellaneous
411 Unavailable operation autom
412 Unavailable operation non autom
413 IOP Communication Failure at startup
Auto Sampler (AS)
414 Sampler Max Plunger speed exceeded
416 Sampler Tray is missing
418 Sampler Vial is unreachable
423 Sampler Vial sensor bad
424 Sampler Column standby timeout expired
425 IOP Skips ADC Reading
426 Sampler Plunger stuck on sensor
427 Sampler Syringe stuck on sensor
SCION Instruments
436-GC/456-GC Service Manual Revision B February 2019
Error level Cause Condition(s)
Alert No communication AS
No response AS-tower. Start AS when AS is turned
Alert
off
Alert Block carrousel when it's turning
Alert Block syringe when it's turning
Hall sensor unplugged Switched to SPME mode
Alert
during syringe use
Alert No Syringe available
No Vial available
Alert
Vial detect should be turned on (setup)
Delay between runs has expired before the second
Alert injection. This error will only appear in dual-/ or
duplicate mode
Run did not start injection. Contact switch on Injector
Alert
broken?
Alert Total Injection volume exceeds syringe volume
Alert Unplugged sensor: sense tower
Alert Carrousel not in place
Alert Unplugged sensor: sled sensor
Alert Unplugged sensor: plunger sensor
Alert Plunger strokes exceed limit
Event Gas saver timeout exceeded
Event Gas saver timeout exceeded
Event Gas saver timeout exceeded
Alert Stopped
Alert Running, remote with compassCDS
Error IOP Communication Failure at startup
Set Injection to 60 μL/se (with testclient) using a 10
Alert
μL syringe
Alert Only on 8410 sampler
Only on 8410 sampler, tray has been turned vial
Alert
becomes unreachable for the tower
Alert Defective sensor
Event Standby timeout expired
IOP too busy (might be due to EFC) and therefore
Error
skips ADC reading
Alert (errors not reproducible)
Alert (errors not reproducible)
GC action
Notification Message
-
-
-
-
-
Notification Message
Notification Message?
Notification Message?
Notification Message?
-
-
-
-
-
Activate standby method
Activate standby method
Activate standby method
Notification Message?
Notification Message?
Notification Message?
Electronics off (all)
H2 flow set to 0.0 mL/min
Notification Message?
Notification Message
Electronics off (all)
H2 flow set to 0.0 mL/min
Activate method, reset time
out
Notification Message?
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Page: 67
510 Error codes
Action needed
switch, jumpers on AS, Reboot GC
Check cables, reboot GC
-
-
-
Recalibrate AS, reboot GC
Place Syringe
Place Vial in position
Remove time out, restart seq.
restart
Check error source
Check source, solve error
Check source, solve error
Check source, solve error
Check source, solve error
Reset plunger stroke counter
Activated method, remove time out
Activated method, remove time out
Activated method, remove time out
Check cause, solve, restart
automation?
Check cause, solve, restart
automation?
Replace/fix IOP
Down load method, reset plunger
speed
Place tray in position
Calibrate AS, place vial, solve
error
Replace vial sensor
Activate method, reset time out
-
-
-