Scion Instruments 436-GC Service Manual page 63

436-GC/456-GC
Code Error Description
49 Rear FID Flame Reigniting
PFPD Board Failure
50 Front PFPD Board Failure
51 Middle PFPD Board Failure
52 Back PFPD Board Failure
53 Becoming Not Ready (during run)
54 Becoming Ready (during run)
IOC Failure
55 IOC Bad Addre Chan
56 IOC Bad Cmd
57 IOC Stepper in Motion
58 IOC Bad Parameter
59 IOC Run mode error
60 IOC no Detector
61 IOC Command not Allowed
62 IOC_EFC_BUFFER_OVERFLOW, Unit rebooted
63 IOC_EFC_COMMUNICATION_ERROR, Unit Rebooted
Zone Open Sensor (zone)
67 Column Oven Open Sensor
68 Zone 1 Open Sensor
69 Zone 2 Open Sensor
70 Zone 3 Open Sensor
71 Zone 4 Open Sensor
72 Zone 5 Open Sensor
73 Zone 6 Open Sensor
Shorted Sensor (zone)
74 Column Oven Shorted Sensor
75 Zone 1 Shorted Sensor
76 Zone 2 Shorted Sensor
77 Zone 3 Shorted Sensor
78 Zone 4 Shorted Sensor
79 Zone 5 Shorted Sensor
436-GC/456-GC Service Manual Revision B February 2019
SCION Instruments
Error level Cause Condition(s)
Alert Defect PFDP board
Alert Defect PFDP board
Alert Defect PFDP board
Event -
Event -
Event -
Event -
Event -
Event -
Event -
Event -
Event -
Caused by too many requests requested by IOC to
Event
EFC Interface print.
Communication between EFC Interface Print and
Event
EFC broken.
Error Column Oven sensor not in use, mis used
Error Zone 1 sensor not in use, mis used
Error Zone 2 sensor not in use, mis used
Error Zone 3 sensor not in use, mis used
Error Zone 4 sensor not in use, mis used
Error Zone 5 sensor not in use, mis used
Error Zone 6 sensor not in use, mis used
Error Shorted sensor. Defect Sensor
Error Shorted sensor. Defect Sensor
Error Shorted sensor. Defect Sensor
Error Shorted sensor. Defect Sensor
Error Shorted sensor. Defect Sensor
Error Shorted sensor. Defect Sensor
GC action
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
-
-
-
-
-
-
-
-
-
GC reboot the interface print
firmware
GC reboot the interface print
firmware
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
H2 flow set to 0.0 mL/min
Electronics off (all)
Page: 62
510 Error codes
Action needed
Replace PFPD board
Replace PFPD board
Replace PFPD board
-
-
-
-
-
-
-
-
-
-
-
Check Column Oven zone
Check zone (1)
Check zone (2)
Check zone (3)
Check zone (4)
Check zone (5)
Check zone (6)
Check Column Oven zone
Check zone (1)
Check zone (2)
Check zone (3)
Check zone (4)
Check zone (5)