Viessmann VITOTROL 100 OT Installation & Service Instructions Manual
Opentherm room temperature controller with digital time switch for vitodens 100-w & vitodens 111-w
Hide thumbs
Also See for VITOTROL 100 OT:
- Operating instructions for the system user (16 pages) ,
- Installation and service instructions manual (28 pages)
Related Manuals for Viessmann VITOTROL 100 OT
Summary of Contents for Viessmann VITOTROL 100 OT
- Page 1 VITOTROL 100 OT Room Temperature Controller Installation & Service Instruction Manual OpenTherm Room Temperature Controller with Digital Time Switch For Vitodens 100-W & Vitodens 111-W...
-
Page 2: Table Of Contents
Contents Contents Preparing for Installation Installation Location for Weather-Compensated Mode Installation Location for Room Temperature-Dependent Mode Specifications Installation Sequence Opening the Controller Fitting the Wall Mounting Base Electrical Connections Assembling the Controller Commissioning & Adjustments Information on Language Setting Starting up the Room Temperature Controller Further Settings Temperature Balancing (Wall Compensation) Start Optimisation... -
Page 3: Preparing For Installation
Preparing Installation Preparing for Installation Installation Location for Weather-Compensated Mode The device can be installed anywhere in the room. Installation Location for Room Temperature-Dependent Mode • On an internal wall in the main living room, approx. 1.5m above the floor •... -
Page 4: Installation Sequence
Installation Sequence Installation Sequence Opening the Controller Fitting the Wall Mounting Base Electrical Connections A. Boiler control unit B. Terminals on the control unit C. Outdoor temperature sensor D. Room temperature controller E. Input for on-site switching contact F. Remove jumper when connecting Recommended connecting cable: •... -
Page 5: Assembling The Controller
Installation Sequence Electrical Connections The following functions can be connected: • Window contact (operation with frost protection temperature when contact is open) • Telephone contact (telephone remote switch) • Presence detector (switching contact) Assembling the Controller... -
Page 6: Commissioning & Adjustments
Commissioning & Adjustments Commissioning & Adjustments Information on Language Setting If a particular language is not available, set the operating language to English. Available languages: • Dutch • English • Polish • German • Spanish • French • Czech • Italian •... -
Page 7: Temperature Balancing (Wall Compensation)
Commissioning & Adjustments Temperature Balancing (Wall Compensation) If the controller is mounted in an unfavourable installation location, the room temperature displayed may deviate from the actual room temperature. The temperature deviation can be adjusted with a correction value. 1. Use <--/--> to select "WALL COMP" 2. -
Page 8: Device Type
Commissioning & Adjustments Device Type The factory setting for "DEVICE TYPE" is "OPEN THERM". If this is not the case, set "OPEN THERM" 1. Use <--/--> to select "DEVICE TYPE" 2. OK to confirm 3. Use +/- or the rotary selector to select "OPEN THERM" 4. -
Page 9: Room Influence Factor
Commissioning & Adjustments The heating curve is limited at the upper end by maximum flow temperature ("MAX TEMP") Maximum Flow Temperature To limit the heating curve at the upper end "MAX TEMP" adjustable from 25 - 80˚C Factory setting 80˚C Room Influence Factor If the actual room temperature deviates too much from the set room temperature, the set flow temperature can be raised by a factor per 1 K deviation. -
Page 10: Selecting The Set Flow Temperature Change Via P-Value
Commissioning & Adjustments Selecting the Set Flow Temperature Change via P Value With the "P-BAND" setting, the change characteristics of the flow temperature are influenced subject to the actual room temperature and the set maximum flow temperature. Example: Maximum flow temperature 80˚C (factory setting) Set room temperature 20˚C Stop hysteresis 0.4K (fixed) "P-BAND"... -
Page 11: Setting The Service Interval
Commissioning & Adjustments Setting the Service Interval "MONTHS BEFORE NEXT SERVICE" adjustable from 1 - 60. Factory setting 00 Soft Start The "SOFT START" function is not active. Emissions Test Function The "CHIMNEY SWEEP" function is not active.