Table of Contents
Advertisement
REMOTE KEYSWITCH OPERATION & WIRING
An optional Remote" Keyswitch may be used for remote arming and disarming (this
is an installer-programmed
option) . A normally–open
momentary
switch
is
connected across Zone 7
(which must be given up as a protection zone).
A
momentary short of the zone will arm the System in the AWAY mode; if the key is
held
(short maintained) for over 3 seconds, the System will arm in the STAY
mode. When a momentary short is applied subsequently, the System will disarm.
A
keyswitch
tamper
(normally-closed) switch wired
in series with zone 7 will
disable keyswitch operation until the system is next disarmed via a keypad, if
activated.
Refer to Diagram 2 for KeysWitch wiring details.
Note:
Regardless
whether End-of–Line supervision is selected or not
(in
Address *41), an end-of–line resistor must still be used for
functioning of the keyswitch.
r -----
-----
____
t
(AHMED}
lREADYI
CONNECTS
TO
REMOTE
KEYPAD
INTERFAcE
ON 4140
(SEE DIAG. 1)
NOTE:
No. 4073.70
IS NOT A
#11~
I
RED
GREEN
REMOTE
I
KEYPAO
CONNECTOR
I
E
I
I
Q
BLUE
[
RED
(PIN
31
TO FLYING
LEAOS
GREEN
ON 10. PIN REMOTE
BLIJE
IPIN
6)
KEYPAO
CONNECTOR
GREEN
IPIN
6)
REO
TAMPER
/
SWITCH
WAC I
I
1
TOTS2-11
-
[
TO414O
I
TERMINAL BLOCK
LOCK
TB2
SWITCH
(N O )
!
TO TB2-10
I
-
I
J
SUGGESTED
PARTS
FoR
REMOTE
KEYSWITCH
I
No, 9787 lVPE
SLIM @XN3LE LEO PLATE
1
No. 112 N,C, TM4PER
SW77CH
I
EOLR
No. 4073.70 HIGN SECURllY
KEYIOCK,
SPRING LOADED IN.O.I
U.L USTEO ITEM.
i
N3707.1O 1O-PIN MALE.TC-MAI.E
AOAPTER [LEO lNTERFiCE)
'
6A4131-10
IWPIN
CONNECTCR
W77N 1.E#Lk3
I
'--------------J
proper
7
I
I
I
I
I
I
I
I
i
I
I
I
I
I
1.
i
I
1
Diagram 2.
KEYSWITCH WIRING
Optional Remote Keypad Connection (4131/4147)
An optional remote keypad (4131 or 4147) may be used with the System. Two 10-pin
female connectors have been supplied for keypad interfacing to the 4140 control
board (see Diagram 1, Summary of Connections) .
Each connector
is
equipped with
color-coded flying leads that are 12 inches (30 cm) in length.
One of the 10-pin connectors is attached directly to the mating 10-pin male
connector on the 4131 or 4147 remote keypad (the connector can only be inserted
one way, and will lock in place) .
The
other
connector
is connected to the 4140 control board via a male-to-
male 10–pin adapter (supplied). See Diagram 1.
INSTALLATION OF No. 4152LM AND WIRING TO
l?o.
4208
The optional No. 4152LM Loop Module is instailed onto the Digital Canmunication
Interface board as follows, referring to Diagram 3.
Note:
The Digital Caomunication Interface board must be mounted onto the
main circuit board (in accordance with the Supplementary Installation
Instructions supplied) before proceeding with steps a, b, and c.
17
Advertisement
Table of Contents
