Simplicity Coronet Series Service & Repair Manual page 106

Ref. Qty. Description
1 1 SPRING, Return
2 A/R WASHER, 3/4
3 1 PULLEY, Idler
4 1 SPRING, Idler
5 1 KLIPRING, 1/2
6 1 PAD, Pedal
7 1 LEVER, Idler, Pulley
8 1 ROD, Clutch, Rear
9 1 ROD, Brake
10 1 ROD, Clutch, Front
11 1 LEVER, Clutch
12 1 BRACKET, Shift
13 1 ROD, Shift, Front
14 1 BAR, Shift, Rear
15 1 TORSION BAR
16 2 BRACKET, Torsion Bar
17 1 PIVOT, Brake
18 1 KLIP RING, 3/8
19 1 SPRING, Compression
20 2 CLEVIS, Idler, Bracket
21 1 PIVOT SHAFT ASSY.
22 1 SPACER, Pivot
TRANSMISSION REMOVAL &
INSTALLATION
1. Remove the mower deck. See Mower Deck Repair.
2. Elevate the rear end. (see Elevating Rear End for
Safe Service) and remove the rear wheels (see Rear
Wheel Removal).
3. Remove the brake return spring (4, Figure 3).
4. Remove the brake lever (41, Figure 2).
5. Disconnect the Neutral Safety Switch (15, Figure 3)
by removing the two small screws under the cover
(2).
6. Disconnect the shift bracket (12, Figure 4) and the
rear shift bar (14, Figure 4).
7. Disconnect both torque straps (19 and 17, Figure 3)
from the transmission and frame.
8. Engage the parking brake.
9. Loosen the transmission mounting bolts (7, Figure 3).
10. Remove the drive belt from the transmission input
pulley.
11. Support the transmission with a floor jack, remove
the mounting bolts, and lower the transmission out of
the carrier assembly making sure it clears all link-
ages.
Install the transmission in reverse order of removal
and perform brake adjustment.
10 Gear Transmission Repair
Ref. Qty. Description
23 2 SPACER
24 1 LOCKWASHER, 1/4
25 2 LOCKWASHER, 5/16
26 2 NUT, Hex, 5/16-18
27 6 COTTER PIN, 3/32 x 3/4
28 4 WASHER, Plain
29 3 WASHER, Plain, 5/16
30 2 NUT, Hex, Nylon Lock, 5/16-18
31 1 WASHER, Plain, 17/64 x 5/8 x 3/64
32 1 SCREW, Hex Hd., 1/4-28 x 5/8
33 2 WASHER
34 2 WASHER, Plain, 1/2
35 4 SCREW, Hex Hd., Flange, Taptite, 5/16-18 x
1/2
36 1 SCREW, Hex Hd., Flange, Taptite, 1/4-20 x
5/8
37 1 NUT, Hex, Flange Lock, 3/8-16
38 1 CARRIAGE BOLT, 5/16-18 x 1
39 1 CARRIAGE BOLT, 5/16-18 x 2-3/4
40 1 CARRIAGE BOLT, 5/16-18 X 1-1/4
41 2 KEY
REMOVE EXTERNAL
COMPONENTS & LINKAGES
1. Remove the input pulley set screw and then remove
the pulley.
2. Remove all external linkages.
10-7
Peerless 915-016B