Table of Contents
Advertisement
CS
PARKING BRAKE CABLE - LEFT REAR (Continued)
(10) Adjust parking brake shoes as necessary.
(Refer to 5 - BRAKES/PARKING BRAKE/SHOES -
ADJUSTMENTS)
PARKING BRAKE CABLE -
RIGHT REAR
REMOVAL
(1) Lock out automatic adjuster in parking brake
lever. (Refer to 5 - BRAKES/PARKING BRAKE -
STANDARD PROCEDURE)
(2) Raise and support vehicle. (Refer to LUBRICA-
TION & MAINTENANCE/HOISTING - STANDARD
PROCEDURE)
NOTE: It may be necessary to back off parking
brake shoe adjustment to allow sufficient slack to
disengage cable buttons from connectors in follow-
ing two steps.
(3) Slide left rear cable button inboard and remove
from equalizer (Fig. 70).
(4) While holding cable connector on end of front
cable secure with a pair of pliers at the front cable
button, slide right rear cable button inboard and
remove from cable connector (Fig. 70).
(5) Access and remove rear hub and bearing.
(Refer to 2 - SUSPENSION/REAR/HUB / BEARING -
REMOVAL)
(6) Remove parking brake cable bolt at knuckle
(Fig. 80).
(7) Remove parking brake shoes from support.
(Refer to 5 - BRAKES/PARKING BRAKE/SHOES -
REMOVAL)
(8) Remove shoe actuator from end of cable and
support (Fig. 81).
(9) Pull cable out of support plate and knuckle.
(10) Place a 13 mm 12-point box wrench over cable
retainer on end of cable housing at crossmember and
collapse retainer fingers (Fig. 82).
(11) Remove cable.
INSTALLATION
(1) Slide leading end of parking brake cable into
hole in flange of crossmember. Slide cable retainer on
end of cable housing into hole until retainer fingers
click into place.
(2) Slide other end of cable through knuckle and
shoe support.
(3) Install shoe actuator on end of parking brake
cable between parking brake shoes (Fig. 81). Make
sure actuator is positioned with word "UP" facing
outward (Fig. 83).
(4) Install parking brake shoes on support. (Refer
to
5
-
BRAKES/PARKING
INSTALLATION)
(5) Install bolt securing parking brake cable to
knuckle (Fig. 80). Tighten bolt to 28 N·m (21 ft. lbs.)
torque.
(6) Install hub and bearing with wheel speed sen-
sor as well as all components necessary to access it.
(Refer to 2 - SUSPENSION/REAR/HUB / BEARING -
INSTALLATION)
(7) While holding cable connector on end of front
cable secure with a pair of pliers at the front cable
button, Place right rear cable button into cable con-
nector (Fig. 70). Release cables allowing button to
seat. It may take some hand pressure to completely
seat button.
(8) Place left rear parking brake cable button into
equalizer (Fig. 70). Release cables allowing button to
seat. It may take some hand pressure to completely
seat button.
(9) Lower vehicle.
(10) Unlock automatic adjuster in parking brake
lever. (Refer to 5 - BRAKES/PARKING BRAKE -
STANDARD PROCEDURE)
(11) Adjust parking brake shoes as necessary.
(Refer to 5 - BRAKES/PARKING BRAKE/SHOES -
ADJUSTMENTS)
PARKING BRAKE LEVER
REMOVAL
(1) Disconnect and isolate battery negative cable
from battery post.
(2) Lock out automatic adjuster in parking brake
lever. (Refer to 5 - BRAKES/PARKING BRAKE -
STANDARD PROCEDURE)
(3) Raise and support vehicle. (Refer to LUBRICA-
TION & MAINTENANCE/HOISTING - STANDARD
PROCEDURE)
NOTE: It may be necessary to back off parking
brake shoe adjustment to allow sufficient slack to
disengage cable buttons from connectors in follow-
ing two steps.
(4) Slide left rear cable button inboard and remove
from equalizer (Fig. 70).
(5) While holding cable connector on end of front
cable secure with a pair of pliers at front cable but-
ton, slide right rear cable button inboard and remove
from cable connector (Fig. 70).
(6) Lower vehicle.
(7) Roll vehicle off hoist as necessary to open left
front door.
(8) Remove left front door opening sill scuff plate.
(9) Remove left front door weather strip.
BRAKES 5 - 45
BRAKE/SHOES
-
Advertisement
Table of Contents
