19-1032; Rev 0; 5/08
General Description
The MAX1455 evaluation kit (EV kit) demonstrates resis-
tive element sensor compensation and calibration using
the MAX1455 and a computer. The kit includes an
assembled and tested PCB, which is available with a
factory-calibrated sensor (MAX1455EVKIT-CS) or with-
out a sensor (MAX1455EVKIT-NS). The software and
computer are not required for performing the initial per-
formance evaluation of the sensor option since the EV
kit is already compensated. A 10-pin ribbon cable con-
nects the EV board to a serial-key adapter,
MAX1452KEY, that plugs into a computer serial port,
allowing the board to be evaluated inside an environ-
mental chamber. The software requires a PC compati-
®
ble with Windows
95/98/2000/XP.
Windows is a registered trademark of Microsoft Corp.
DESIGNATION
QTY
C1
1
470µF 10V electrolytic capacitor
C2, C4, C6
3
0.1µF X7R ceramic capacitors
C3, C5
2
1µF X7R ceramic capacitors
D1
1
5.6V Zener diode
D2
0
Dual diode, not installed
J1
0
2-pin header, not installed
-CS
0
J2
-NS
1
J3
1
2-pin header
-CS
1
J4
-NS
0
P1
1
10-pin header
4mm banana sockets;
P2, P3, P4
3
connect +5V, GND, OUT
R1
1
10Ω ±5% resistor
R2
1
4.7kΩ ±5% resistor
R3
1
10Ω ±5% resistor
R4
1
30Ω ±5% resistor
NovaSensor (Fremont, CA)
S1
1
NPH-8-100GH
(8-pin TO package, 100kPa gauge)
S2
0
Unused, alternate sensor site
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim's website at www.maxim-ic.com.
DESCRIPTION
2-pin header, not installed
2-pin header—shorted
2-pin header—shorted
2-pin header, not installed
MAX1455 Evaluation Kit
♦ Proven PCB Layout
♦ Convenient On-Board Test Points
♦ Fully Assembled and Tested
♦ Optional Pressure Sensor (MAX1455EVKIT-CS)
♦ Factory-Calibrated Over Temperature
(MAX1455EVKIT-CS)
♦ LabVIEW
®
-Based Software
LabVIEW is a registered trademark of National Instruments, Corp.
PART
MAX1455EVKIT-CS
MAX1455EVKIT-NS
MAX1452KEY*
* MAX1452KEY is also used for MAX1455EVKIT and is included
in MAX1455EVKIT package.
EV Kit Component List
DESIGNATION
QTY
S3
1
SP1–SP4
4
SP5
1
U1
1
U1
1
DESIGNATION
QTY
C1
1
C2, C3, C5
3
C4
1
Features
Ordering Information
TYPE
EV Kit
EV Kit
Serial Key Adapter
DESCRIPTION
8-pin DIL header, alternate sensor
connector
Split pads;
cut tracks to allow connection of
sensor at S3
Split pad;
confi g ur e on- b oar d op am p as b uffer ;
cut tracks to allow use of op amp
MAX1455AAE
MAX1455AAP
KEY Component List
DESCRIPTION
220µF 10V electrolytic capacitor
(radial lead)
Panasonic ECE-A1AKA221
Digi-Key P832-ND
0.33µF ±10%, 25V X7R ceramic
capacitors* (1206)
Taiyo Yuden TMK316BJ334KF or
equivalent
Murata GRM319R71E334K
0.047µF ±10%, 50V X7R ceramic
capacitor (1206)
KEMET C1206C473K5RACTU
Digi-Key 399-1246-1-ND
1