1. Manuals
  2. Brands
  3. Hoshizaki Manuals
  4. Ice Maker
  5. KMD-460MAJ
  6. Instruction manual

Hoshizaki KMD-460MAJ Instruction Manual

Modular crescent cuber
Hide thumbs Also See for KMD-460MAJ:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
Instruction Manual
Modular Crescent Cuber
Models
KMD-460MAJ, MWJ
hoshizakiamerica.com
Issued: 8-31-2018

Advertisement

Table of Contents
loading

Related Manuals for Hoshizaki KMD-460MAJ

Summary of Contents for Hoshizaki KMD-460MAJ

  • Page 1 Instruction Manual Modular Crescent Cuber Models KMD-460MAJ, MWJ hoshizakiamerica.com Issued: 8-31-2018...
  • Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, send an e-mail message, or write to the Hoshizaki Technical Support Department for assistance. Phone: 1-800-233-1940; (770) 487-2331 Fax: 1-800-843-1056;...

  • Page 3: Table Of Contents

    IMPORTANT This manual should be read carefully before the appliance is installed and operated. Read the warnings and guidelines contained in this manual carefully as they provide essential information for the continued safe use and maintenance of the appliance. Retain this manual for any further reference that may be necessary. CONTENTS Important Safety Information ....................

  • Page 4: Important Safety Information

    Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, damage to the appliance, or damage to property. WARNING Indicates a hazardous situation which could result in death or serious injury.
  • Page 5 WARNING, continued • Children should be properly supervised around the appliance. • Do not climb, stand, or hang on the appliance or allow children or animals to do so. Serious injury could occur or the appliance could be damaged. • Do not use combustible spray or place volatile or flammable substances near the appliance.

  • Page 6: Specifications

    The nameplate is located on the rear panel. For certification marks, see the nameplate. We reserve the right to make changes in specifications and design without prior notice. 1. KMD-460M_J Single Phase Model Number KMD-460MAJ KMD-460MWJ AC Supply Voltage 115/60/1 115/60/1 Compressor 115V 8.6RLA 54.5LRA...

  • Page 7: Dimensions/Connections

    B. Dimensions/Connections Units: mm [in.] 1. Air-Cooled Models (MAJ) Rear Side ELECTRICAL SUPPLY OPENING 22 [7/8] DIA ICEMAKER WATER INLET 1/2” FPT M5 MOUNTING HOLES ICEMAKER DRAIN OUTLET 3/4” FPT [2-5/8] [2-7/8] [3-1/8] [3-1/8] [22-7/8] [24-1/8] Bottom KMD-460MAH A 768 [30-1/4] [9-3/8] [13] [1-1/2]...

  • Page 8: Water-Cooled Models (Mwj)

    2. Water-Cooled Models (MWJ) Units: mm [in.] Rear Side ELECTRICAL SUPPLY OPENING 22 [7/8] DIA ICEMAKER WATER INLET 1/2” FPT CONDENSER WATER INLET 1/2” FPT CONDENSER WATER OUTLET 3/8” FPT M5 MOUNTING HOLES ICEMAKER DRAIN OUTLET 3/4” FPT [3/8] [2-5/8] [2-7/8] [3-1/8] [3-1/8]...

  • Page 9: Installation And Operating Instructions

    II. Installation and Operating Instructions WARNING • The icemaker must be installed in accordance with applicable national, state, and local codes and regulations. • Failure to install, operate, and maintain the icemaker in accordance with this manual will adversely affect safety, performance, component life, and warranty coverage and may result in costly water damage.

  • Page 10: How To Remove Panels

    • The icemaker can be installed on a dispenser unit or storage bin 30" wide or wider. The following are recommended: Hoshizaki Dispenser, Model DB-200 or DM series; Hoshizaki Ice Storage Bin, Model B-500 series. For further options, contact your local Hoshizaki distributor.

  • Page 11: Setup

    2) Position the dispenser unit/ice storage bin in its permanent location. 3) If required, install an adapter kit or top kit. Contact your local Hoshizaki distributor for recommendations. 4) Level the dispenser unit/ice storage bin in both the left-to-right and front-to-rear directions.

  • Page 12: Bin Control Installation

    2. Bin Control Installation 1) Remove the control box cover. Remove the 2 thumbscrews securing insulation panel (B), then remove insulation panel (B). See Fig. 3. 2) Disconnect the discharge hose from the pump motor, then disconnect the drain valve drain hose and the overflow drain hose. 3) Disconnect the pump motor connector from the back of the control box, then disconnect the float switch connector from the control board.
  • Page 13 7b) Coca-Cola Freestyle Dispenser or Dispenser Unit with Thick Adapter Application: ® Remove the extension bracket and 2 thumbscrews from the accessory bag. Secure the bin control to the extension bracket using the 2 thumbscrews. See Fig. 6. Secure the extension bracket to the rear interior wall using the 2 thumbscrews on the rear interior wall.

  • Page 14: Electrical Connection

    E. Electrical Connection WARNING For All Models • Electrical connection must be hard-wired and must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric shock, serious injury, fire, or damage. •...

  • Page 15: Water Supply And Drain Connections

    • External filters, strainers, or softeners may be required depending on water quality. Contact your local Hoshizaki Certified Service Representative or local Hoshizaki distributor for recommendations. • A plumbing permit and services of a licensed plumber may be required in some areas.

  • Page 16: Icemaker

    (5 cm) vertical air Bin Drain Outlet gap between the end of 3/4" FPT each pipe and the drain. 2-inch (5-cm) air gap Minimum 3/4" Nominal ID Hard Pipe or Equivalent Fig. 8 Air-Cooled Models Floor Drain Model Shown: KMD-460MAJ...

  • Page 17: Water-Cooled Condenser

    2. Water-Cooled Condenser a) Connection to an Open Drain System Condenser Water Minimum Condenser Condenser Drain Minimum Condenser Supply Inlet Water Supply Line Size Outlet Drain Line Size 1/2" Female Pipe 1/4" Nominal ID Copper 3/8" Female Pipe 1/4" Nominal ID Hard Pipe Thread (FPT) Water Tubing or Equivalent Thread (FPT)
  • Page 18 b) Connection to a Closed Loop System Condenser Water Minimum Condenser Condenser Minimum Condenser Supply Inlet Water Supply Line Size Return Outlet Return Line Size 1/2" Female Pipe 1/4" Nominal ID Copper 3/8" Female Pipe 1/4" Nominal ID Copper Thread (FPT) Water Tubing or Equivalent Thread (FPT) Water Tubing or Equivalent...

  • Page 19: Final Checklist

    G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the dispenser unit/ice storage bin. 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water temperature within 45°F to 90°F (7°C to 32°C) all year around? 3) Air-Cooled Models: Is there at least 6"...

  • Page 20: Startup

    H. Startup WARNING All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. NOTICE • If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. •...

  • Page 21: Maintenance

    III. Maintenance The appliance must be maintained in accordance with the instruction manual and labels provided. Consult with your local Hoshizaki Certified Service Representative about maintenance service. WARNING • Only qualified service technicians should service the appliance. • To reduce the risk of electric shock, do not touch the control switch or service switch with damp hands.

  • Page 22: Cleaning And Sanitizing Instructions

    "SERVICE" position. 1. Cleaning Procedure 1) Dilute 9.5 fl. oz. (281 ml) of Hoshizaki "Scale Away" with 1.8 gal. (6.8 l) of warm water. 2) Remove all ice from the evaporator and the dispenser unit/ice storage bin. Note: To remove cubes on the evaporator, turn off the power supply and turn it back on after 3 minutes.
  • Page 23 8) In bad or severe water conditions, clean the float switch as described below. Otherwise, continue to step 9. a. Remove the control box cover. Remove the 2 thumbscrews securing insulation panel (B), then remove insulation panel (B). See Fig. 19. b.

  • Page 24: Sanitizing Procedure - Following Cleaning Procedure

    17) Turn off the power supply, then remove the front panel. 18) Move the control switch to the "ICE" position. 19) Replace the front panel in its correct position. 20) Turn on the power supply to fill the water tank with water. 21) Turn off the power supply after 3 minutes.
  • Page 25 15) Replace the front panel in its correct position. 16) Clean the dispenser unit/storage bin liner using a neutral cleaner. Rinse thoroughly after cleaning. 17) Turn on the power supply to start the automatic icemaking process.

  • Page 26: Preparing The Icemaker For Periods Of Non-Use

    IV. Preparing the Icemaker for Periods of Non-Use NOTICE • When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. • The pump motor is energized continuously when the control switch is in the "SERVICE"...
  • Page 27 3) Open the condenser water supply line drain valve. If connected to a closed loop system, also open the condenser return line drain valve. 4) Attach a compressed air or carbon dioxide supply to the condenser water supply line drain valve. 5) Open the water regulating valve by using a screwdriver to pry up on the spring retainer underneath the spring.

  • Page 28: Disposal

    V. Disposal The appliance contains refrigerant and must be disposed of in accordance with applicable national, state, and local codes and regulations. Refrigerant must be recovered by properly certified service personnel.
  • Page 29 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A5296-010...

This manual is also suitable for:

Kmd-460mwj

Table of Contents