Vermont Castings Stardance SDDVTCBSB Installation & Operating Manual

Direct vent gas heater
Hide thumbs Also See for Stardance SDDVTCBSB:

Advertisement

Installation & Operating Manual
Installation and Appliance Setup - Care and Operation
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Call your dealer for questions on Installation, Operation, or Service.
NOTICE: SAVE THESE INSTRUCTIONS
SDDVT Series Stardance
Direct Vent Gas Heater
Models:
SDDVTCBSB, SDDVTBSSB, SDDVTBDSB,
SDDVTBMSB, SDVTSCCB, SDVTSCBS,
SDVTSCBD, SDVTSCBM
CERTIFIED
S
B
AFETY
ARRIER
Installation and service of this appliance should be performed by
1
®
Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result
in serious injury, death or property damage.
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
– Do not try to light any appliance.
– Do not touch any electrical switch; do not use
any phone in your building.
– Leave the building immediately.
– Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
– If you cannot reach your gas supplier, call the
Installation and service must be performed
gas supplier.
DANGER
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this
appliance and shall be installed.
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
3-90-20306760

Advertisement

Table of Contents
loading

Summary of Contents for Vermont Castings Stardance SDDVTCBSB

  • Page 1 Installation and service of this appliance should be performed by NEVER ALLOW CHILDREN TO TOUCH GLASS. A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 2: Table Of Contents

    Vertical Side Wall Installation Optional Accessories Limited Lifetime Warranty (Millivolt Only) Thermostat Connection (optional) = Contains updated information Command Center Wall Installation Wall Switch Installation Burner Information Install the Safety Barrier Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 3: Important Safety Information

    This appliance may be installed in an aftermarket* manufactured WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 4: Massachusetts Safety Information

    (1/2) inch in size, This product and the fuels used to operate this product Stardance Direct Vent Gas Heaters Inspection unless, upon inspection, the inspector observes carbon Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 5: Pre-Installation

    (178 mm) 12-5/8” (321 mm) 2-7/8” (73 mm) Flue Collar L C 26-3/4" (680 mm) Supply Inlet 3" (76 mm) 14-1/2" 25-1/2" (355 mm) (648 mm) Figure 1 - Stardance dimensions. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 6: Installation Requirements

    In choosing a location for the stove, consider: • The location of outside walls; • • • NOTE: to shrink, or may adversely affect the binders in the wallpaper Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 7: Parallel Installation

    B Minimum Clearance Sidewall Clearance Stove Clearances Pipe Centerlines Figure 6 - Dimensions and clearances to ceiling or alcove. Hearth Requirements When the heater is installed directly on any combustible Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 8 9 10 11 12 13 14 15 16 17 18 19 20 Horizontal Run (in feet) WARNING to this manual for correct installation and operational pro- Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 9: Vertical Termination

    Horizontal Run (in feet) from center to top of slot to top of slot from center of screw to of screw to Figure 8 - Vertical vent termination window. plate plate Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 10: Vent Termination Clearances

    For installations using DuraVent pipe, parallel installations with minimum wall clearance have restricted access for connecting the Horizontal Vent Cap straps to the vent pipe. See the maker’s instructions for recommended installation procedures. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 11 2' (610 mm) from the center line of the terminal 3' (91cm) 3' (91cm) other appliance † † driveway located on public property ‡ ‡ balcony Figure 11 - Vent termination clearances. NOTE: Codes ‡ Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 12 = 8’ (2.4 m) Min. Caps 3’ (914 mm) Combustible & Noncombustible Combustible & M = 12" (305 mm) Noncombustible P = 6” (152 mm) 12" (305 mm) *NOTE: Figure 12 - Termination clearances. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 13 DuraVent Components sections) HHT Components* Wall Plate Wall Strap (includes storm collar) Decorative Wall Thimble Cover Storm Collar Wall Thimble Wall Thimble Wall Thimble Cover (Brass) Wall Thimble Cover (Brass) CCSLP Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 14: Assembly & Installation

    Install the Optional Fan – SDDVT models (Millivolt Only - See page 27 for SC Models) Rear Skirt Insert Figure 16 - Remove rear shroud. includes a ‘snapstat’ which automatically turns the fan Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 15 Star Washer Sheet Metal Screws Snapstat Phillips Bolts Star Washer Snapstat Bracket NOTE: Rheostat Rheostat Figure 18 preinstalled) Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 16: Important Safety Information

    Finishing Material (Vinyl Siding, etc.) WARNING Before You Start WARNING Important Safety Information Tools: Pliers Square • Building Supplies: • The installation must conform with local codes or in the Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 17 The Stardance is approved for installation only with the Approved Vent System Install the Vent Adapter Pipe (HHT SLP Vent Components) Drill three pilot holes into the Inner Starter and secure Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 18: Secure The Vent Sections

    (see WARNING CORRECT INCORRECT Figure 22 - Make sure the seams are not aligned to prevent unintentional disconnection. Figure 25 - Securing Vertical Pipe Sections Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 19: Disassemble Vent Sections

    CAUTION Risk of Burns! Local codes may require installation of a Figure 28 - Align and Disassemble Vent Sections Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 20: Divert Roof Run-Off

    (244 mm) Opening for Noncombustible Wall Install gutter (190 mm) Install L-shaped diverter Vertical Side Wall Installation: adjustments for vertical vent runs. NOTE: Always install vertical side wall horizontal venting Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 21 NOTE: Support horizontal pipes every 5' (152 cm) with metal pipe straps. Recessed Wall Sheet Metal Collar Screws and Bracket Wall Screws Waterproof Seal Wall Plate Termination Cap recessed wall. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 22 Wall Screws Waterproof Seal Snorkel Termination Cap Drain Window Well RADIANCE Vertical Through-The-Roof Application/installation Note: Figure Example: • Two sets of 45° elbow offsets may be used within the Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 23 The heater is shipped from the factory as a Direct Vent Support Plate NOTE: The restrictor plate supplied with the stove is not used for Natural Vent applications. Trim Plate Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 24 (if any) toward the wall; sections usually do not need to be includes a slip section, this should be the last section of Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 25 A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed. Install Log Set Raised - Completed Installation Pilot Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 26: (Millivolt Only)

    ON/OFF Switch or Millivolt Thermostat with local codes or in the absence of local codes, with the Thermostat or wall switch Connection (optional): CAUTION Thermostat Wire / Gauge Maximum Run Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 27: Command Center Wall Installation

    Install the Fan – SDVTSC Models • • • Command Center Wall Installation • The command center may be mounted on the wall with the Wall Switch Installation WARNING Figure 51 - Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 28: Burner Information

    THIS APPLIANCE SHOULD BE CONNECTED TO THE GAS SUPPLY ONLY BY A QUALIFIED GAS SERVICE TECHNICIAN. FOLLOW ALL LOCAL CODES. THERE MUST BE A GAS SHUT-OFF BETWEEN THE STOVE AND THE SUPPLY. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 29 Gas Out Gas In Pilot Gas Tubing Valve Figure 52 To Junction Box In Fireplace Light WHITE BLACK WHITE BLACK BLACK Optional WHITE GREEN Connector Pin To Contro l Box Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 30: Install The Safety Barrier

    UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS. A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed. Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 31: Operating Instructions

    Pilot and Burner Inspection SDDVT MODELS Sensor SDVTSC MODELS Thermopile Figure 55 Figure 56 Flame & Temperature Adjustment Turn Turn clockwise counterclockwise to decrease to increase flame height flame height Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 32 (1) minute after the pilot • If knob does not pop up when released, stop and SIT NOVA To Turn Off Gas To Heater Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 33 Corrective Action electrode at pilot button) Pilot will not stay lit after carefully (thermocouple), remote wall switch instructions defective • • • operator the pilot safety to drop out vent terminal Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 34 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING personal injury or loss of life. WHAT TO DO IF YOU SMELL GAS: Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 35 LIGHTING AND OPERATING INSTRUCTIONS FOR RADVTSC MODELS Master Switch Command Center TO TURN OFF GAS TO APPLIANCE Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 36: Signature Command Operating Instructions

    • Low battery Indication for Transmitter • Child Proof Lock-out • Security Codes (16) • Countdown 6 hr Timer • Standard Thermostatic Control Mode Modulation) • Three Speed Control for Blower Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 37 NOTE: By disabling this feature, your stove may continue to operate unattended. Function Operation Default Setting Intermittent Pilot the main burner is off) Learn Remote Transmitter (Beep twice then press any handheld remote button) Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 38: Operating Instructions

    Function Areas of the LCD Display Information Bar The information bar shows the room temperature, the Down Turning the Stove Off • The room temperature will always be shown after Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 39 The touch area contains all touch buttons to control the four batteries are installed, the transmitter will Battery Door Tabs Logo Bar Changing Temperature Unit When batteries are installed in the transmitter, all available The transmitter enters Manual Mode Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 40 General • • • The transmitter will operate the remote receiver from 1 foot Resetting the Transmitter Manual Mode • • • • Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 41 3 seconds Mode • Icon the stove will be shut down completely when the timer transmitter will automatically • • between the set temperature • Figure 66 Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 42 To exit Smart Mode ® thermostat and shut off the stove; To shut off the Smart Mode thermostat option and return Blower Speed Control The blower speed control function Figure 68 Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 43 Childproof indicator will be shown on the • • Using the Mounting Base Safety Features Low Battery Detection When low battery condition occurs, the transmitter will • Power On Initialization Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 44: Troubleshooting

    The sensor on the pilot Adjust sensor position Main burner doesn’t Go through is not in the flame or replace the pilot light (pilot flame too small)? Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 45 Burner, Pilot and Control Compartment WARNING Pilot Flame Burner Burner Flame Sensor Thermopile Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 46: Fuel Conversion

    • Check that the screw is clean and if necessary remove NOTE: Do not over-tighten the screw. Recommended to grip the wrench by the short side. Shut Main Valve Line Conversion Precautions Conversion Procedure Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 47 Bottom View NOTE: It is not necessary to remove the pilot tube for conversion. Pilot Figure 81 Venturi Bracket Bracket Pilot hood Pilot bracket Pem Studs Figure 82 Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 48 Bracket Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 49 SDVTSC Models All Models Figure 85 Figure 86 Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 50 Conversion to LP* Input (BTU/h) Model Minimum SDDVT 20308650 21,000 25,000 SDVTSC 4604-011 Conversion to Natural Gas Input (BTU/h) Model Minimum SDDVT 4604-012 4604-316 20,000 28,000 SDVTSC 4604-013 Model Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 51: Cleaning & Maintenance

    TO TOUCH GLASS. A barrier designed to reduce the risk of burns from Care of Cast Iron the hot viewing glass is provided with this appliance and shall be installed. CAUTION Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 52 Glass Replacement 87 and 88 and previous instructions for removal of the Inspect the Vent System Annually Check the Gas Flame Regularly Gasket Replacement Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 53: Wiring Diagrams

    NOTE: If any of the original wire, as supplied with the appliance, must be replaced, it must be replaced with Chassis Ground RHEOSTAT / SNAPSTAT Optional Blower Kit Schematic Diagram MOTOR SNAPSTAT ON/OFF RHEOSTAT Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 54 Control Board to Solenoid Gas Out Gas In Pilot Gas Tubing Valve To Junction Box In Fireplace Light WHITE BLACK WHITE BLACK BLACK Optional WHITE GREEN Connector Pin To Contro l Box Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 55: Service Parts List

    SDDVTCSBMSB (Majolica Brown) - End Manufacturing Date: October 2015 SDVTSCBD (Bordeaux) SDDVTBDSB (Bordeaux) SDDVTCSBDSB (Bordeaux) - End Manufacturing Date: October 2015 20 21 Part number list on following page. 11/18 Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 56 Gasket, Glass (Medium Knit) 1203702K Nut, Hex Jam 3/8-16 TOPLK-Z Pkg of 10 1203290-10 Pawl Assembly, Ash Door 30002362 Front Steel Handle/Shaft - NI/VER 30002717 Additional service parts on following page Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 57 AC Module SCS w/8’ Power Cord SDVTSC Series Only 3007360 Pilot Assembly SDVTSC Series Only 20308981 Handle Package w/Screw Wood 30004175K Switch Bracket 53821K Additional service parts on following page Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 58 Control Plate Assembly (Burner, Valve, Pilot) 20012493 Conversion Kits Conversion Kit, NG to LP 20012735K SDDVT Conversion Kit, LP to NG 4604-012 Conversion Kit, NG to LP 4604-011 SDVTSC Conversion Kit, LP to NG 4604-013 Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 59: Optional Accessories

    Classic Black 2684 Biscuit Shelf Installation Maintenance Remote Controls – SDDVT The remote control allows you to turn the heater on or off ON/OFF Remotes ON/OFF Thermostat Remote RCB,RCMT TSST, RCST Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...
  • Page 60: Limited Lifetime Warranty

    Hearth & Home Technologies LIMITED LIFETIME WARRANTY Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT gas, wood, pellet and electric hearth appliances that are purchased from an HHT authorized dealer. WARRANTY COVERAGE: WARRANTY PERIOD: is produced in the following table.
  • Page 61 WARRANTY CONDITIONS: other than the dealer from whom you originally purchased the product. • Limited Catalyst Warranty Amount of Time Since Purchase Credit Towards Replacement Cost WARRANTY EXCLUSIONS:...
  • Page 62 This warranty is void if: • There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited LIMITATIONS OF LIABILITY...
  • Page 64 Based on CSA P.4.1-2015 EFFICIENCY RATINGS ENERGUIDE RATINGS D.O.E. STOVE EFFICIENCY MODEL PERCENTAGE (AFUE PERCENTAGE) SDDVT Series SDVTSC Series Vermont Castings • Stardance SDDVTSB Installation Manual_R18 • 11/18 3-90-20306760...

Table of Contents