Spa Control Operation - Marquis Epic Owner's Manual

SPA CONTROL OPERATION

9-Button: Show
8-Button: Epic, Euphoria, Promise 2P, Resort, Reward, Wish
7-Button: Spirit, Mirage, Promise 1P, Rendezvous
PUMP PRIMING (Pr)
Pump priming feature begins at start-up. When your spa is energized, the LCD
window displays a "Pr" message. This mode lasts approximately four to five
minutes, if not exited manually by pressing the TEMP+ pad.
Your hot tub has been configured at the factory to run without any additional
programming changes other than setting the desired temperature. We do
however recommend that the time is set as this will be shown in the display as a
convenience and aids in controlling when the hot tub will filter. See "changing
the system settings" below on setting the time.
The hot tub controls are state of the art and will retain all of the settings or
changes that have been made in the event of a power failure.
CONTROL PANEL OPERATION INSTRUCTIONS
HOT KEYS
Using pump 1:
Pressing the Jets 1 button will turn pump 1 on low speed. Pressing a second
time will turn the pump on high speed. Pressing the button a third time will turn
the pump off. The pump will run for 15 minutes before shutting off or switching to
low speed. If the pump continues to run on low speed after the 15 minute
timeout, the system is either calling for heat or has entered into a filtration cycle.
Using pump 2 (if equipped):
Pressing the Jets/1 button will turn pump 1 on low speed. Pressing a second
time will turn the pump on high speed. Pressing the button a third time will turn
the pump off. The pump will run for 15 minutes before shutting off or switching to
low speed.
Using pump 3 (if equipped):
Pressing the Jets/1 button will turn pump 1 on low speed. Pressing a second
time will turn the pump on high speed. Pressing the button a third time will turn
the pump off. The pump will run for 15 minutes before shutting off or switching to
low speed.
Light:
Pressing the light button will turn the LED lights on. Pressing a second time will
turn them off. If left on the LED lights will automatically turn off after 30 minutes.
Special light feature: You can change the color of the LED lights by pressing the
light button repeatedly within 3 second intervals. Doing this will allow you to
scroll and choose a specific color or light sequence.
ALL QUIET SOAK FEATURE
Pressing the soak button activates a special feature that turns off all pumps and
heater, allowing for a quite soak in the hot water. Pressing the button a second
time will restore the unit back to normal operation. If left on, the soak mode will
time out after 15 minutes and revert back to normal operation.
Note: Periodically the pump/s may continue to operate for a short time after
pressing the soak button. This typically happens when the spa is in a heat cycle
as the heater will need a short period to cool down before stopping the water
flow.
SETTING THE TEMPERATURE
Pressing the temp up or temp down buttons allow you to adjust the heat to the
desired temperature. The set temperature is shown in the left hand side of the
LCD display. Pressing and holding the temp up or temp down button will allow
for an accelerated change of the temp.
Factory default temperature: 38°C
Maximum set temperature: 40°C
Minimum set temperature: 16°C
CHANGING THE SYSTEM SETTINGS
A few basic keystrokes will allow for easy navigation of the available
programming options. The settings, soak, temp up and temp down buttons also
serve as side to side and up and down navigation controls when in the menu.
Note the arrows on the buttons. The back/set button in the center is used to
save a setting or go back one screen at a time.
Tip! Note that the menu item that is selected will be brighter in the display than
the others indicating where you are in the menu.
Tip! If you have accidentally entered the setting menu, simply press the back/set
button or wait 30 seconds to go back to the home screen.
Programming choices shown in the main and sub menus. (See definitions of
menu and sub menu items.)
Heat Mode (main menu item)

Ready
 Rest
Time of day (main menu item)
 Current set time
Filter cycles (main menu item)
 Filter cycle 1 and filter cycle 2
Preferences (main menu item)
 Temp display – Choose between Fahrenheit "F" or Celsius "F"

Time display – choose between 12 or 24 hour display
 Cleanup – choose the length of time of the clean-up cycle

Language – choose between English, Spanish, French or German
Diagnostics (main menu item

Spa
 Information
 A/B Temps

Fault Log
To make a change, perform the following sequence
1. Press the setting button to display the main settings menu
2. Press the settings button to move over into the main settings
menu
3. Scroll down by pressing the temp down button to the desired
menu item
4. Press the settings button to move into the sub menu
5. Press the temp up or temp down to change the parameters
(Note if a change is made, the save and cancel icons appear
on the left hand side of the screen)
6. Press the soak button to move to the left to the save icon.
Note the save icon will be brighter than everything else.
7