Customizing The My Day Widget; Customizing The Controls Menu; Watch Face Settings; Customizing The Watch Face - Garmin MARQ DRIVER Owner's Manual

Blue bars indicate periods of rest. Yellow bars indicate
periods of stress. Gray bars indicate times that you were too
active to determine your stress level.
3 To start a breathing activity, select DOWN > START, and
enter a duration for the breathing activity in minutes.

Customizing the My Day Widget

You can customize the list of metrics displayed on the My Day
widget.
1
From the watch face, select UP or DOWN to view the My
Day widget.
2
Hold MENU.
3 Select Options.
4
Select the toggle switches to show or hide each metric.

Customizing the Controls Menu

You can add, remove, and change the order of the shortcut
menu options in the controls menu
page 1).
1
Hold MENU.
2
Select Controls.
3
Select a shortcut to customize.
4
Select an option:
• Select Reorder to change the location of the shortcut in
the controls menu.
• Select Remove to remove the shortcut from the controls
menu.
5
If necessary, select Add New to add an additional shortcut to
the controls menu.

Watch Face Settings

You can customize the appearance of the watch face by
selecting the layout, colors, and additional data. You can also
download custom watch faces from the Connect IQ store.

Customizing the Watch Face

Before you can activate a Connect IQ watch face, you must
install a watch face from the Connect IQ store
Features, page 9).
You can customize the watch face information and appearance,
or activate an installed Connect IQ watch face.
1
From the watch face, hold MENU.
2
Select Watch Face.
3
Select UP or DOWN to preview the watch face options.
4
Select Add New to scroll through additional pre-loaded watch
faces.
5
Select START > Apply to activate a pre-loaded watch face or
an installed Connect IQ watch face.
6
If using a pre-loaded watch face, select START >
Customize.
7
Select an option:
• To change the style of the numbers for the analog watch
face, select Dial.
• To select a race track outline to appear on the driving-
specific analog watch face, select Race Track.
• To change the style of the hands for the analog watch
face, select Hands.
• To change the style of the numbers for the digital watch
face, select Layout.
• To change the style of the seconds for the digital watch
face, select Seconds.
• To change the data that appears on the watch face, select
Data.
Customizing Your Device
(Viewing the Controls Menu,
(Connect IQ
• To add or change an accent color for the watch face,
select Accent Color.
• To change the background color, select Bkgd. Color.
• To save the changes, select Done.

Sensors Settings

Compass Settings

Hold MENU, and select Sensors & Accessories > Compass.
Calibrate: Allows you to manually calibrate the compass sensor
(Calibrating the Compass Manually, page
Display: Sets the directional heading on the compass to letters,
degrees, or milliradians.
North Ref.: Sets the north reference of the compass
North Reference, page 31).
Mode: Sets the compass to use electronic-sensor data only
(On), a combination of GPS and electronic-sensor data when
moving (Auto), or GPS data only (Off).

Calibrating the Compass Manually

Calibrate the electronic compass outdoors. To improve heading
accuracy, do not stand near objects that influence magnetic
fields, such as vehicles, buildings, and overhead power lines.
Your device was already calibrated at the factory, and the
device uses automatic calibration by default. If you experience
irregular compass behavior, for example, after moving long
distances or after extreme temperature changes, you can
manually calibrate the compass.
1
Hold MENU.
2
Select Sensors & Accessories > Compass > Calibrate >
Start.
3
Follow the on-screen instructions.
TIP: Move your wrist in a small figure eight motion until a
message appears.

Setting the North Reference

You can set the directional reference used in calculating
heading information.
1 Hold MENU.
2
Select Sensors & Accessories > Compass > North Ref..
3 Select an option:
• To set geographic north as the heading reference, select
True.
• To set the magnetic declination for your location
automatically, select Magnetic.
• To set grid north (000º) as the heading reference, select
Grid.
• To set the magnetic variation value manually, select User,
enter the magnetic variance, and select Done.

Altimeter Settings

Hold MENU, and select Sensors & Accessories > Altimeter.
Calibrate: Allows you to manually calibrate the altimeter sensor.
Auto Cal.: Allows the altimeter to self-calibrate each time you
turn on GPS tracking.
Elevation: Sets the units of measure for elevation.
Calibrating the Barometric Altimeter
Your device was already calibrated at the factory, and the
device uses automatic calibration at your GPS starting point by
default. You can manually calibrate the barometric altimeter if
you know the correct elevation.
1
Hold MENU.
2
Select Sensors & Accessories > Altimeter.
31).
(Setting the
NOTICE
31