Fx Loop; Power; Loudspeaker; Foot Controller - Marshall Amplification MG GOLD SERIES Owner's Manual

OVERVIEW

FX LOOP

The FX Return socket (24) on the rear
panel is used to connect the OUTPUT of
the effects processor or pedal you are
using in the effects loop.
The FX loop is series and set at instrument
level so both guitar FX or professional
rack effects units can be connected.
The FX Send socket (25) on the rear panel
is used to connect to the INPUT of the
unit you are using in the effects loop.
The FX loop is switched on and off via the
Ext FX switch (15) on the front panel.

LOUDSPEAKER

ALWAYS USE A NON-SCREENED
MARSHALL APPROVED SPEAKER LEAD
WHEN CONNECTING AN EXTENSION
CABINET TO THESE AMPLIFIERS.
MG101FX/MG102FX
The single Loudspeaker socket (22) is used
to connect either the internal speaker or
an external speaker cabinet to the unit's
power amp. When using external cabinets
ensure the total load impedance is equal
to, or exceeds, 4 ohms.
MG100HFX
The two Loudspeaker sockets are used to
connect to 1 or 2 external cabinets. When
using external cabinets ensure the total
load impedance is equal to, or exceeds, 4
ohms.

POWER

The Power switch (20) turns the amplifier
on and off. If current settings have not
been stored they will be lost.
RESTORING SETTINGS - WARNING: ALL AMP
& FOOTSWITCH SETTINGS WILL BE LOST
To restore the unit to factory settings (see
handbook rear cover) you must hold the
Store switch (19) while powering on the
amplifier. The Clean/Crunch (3) and OD
(5) lights will light orange. You can then
release the Store switch (19).
Resetting the amplifier will erase all
user Channel presets and all user
Footcontroller allocations, replacing them
with the factory presets.
ENGLISH
FOOTCONTROLLER
STOMPWARE PEDL-90008 (OPTIONAL)
1 1
2 2
1
1. FOOTSWITCH
Each footswitch can be assigned a
different stored function.
2. DIGITAL DISPLAY
This display indicates the various
functions of the footcontroller.
3. LED STATUS PANEL
This always reflects the current status of
the amplifier or tuner details:
CLN & OD: Current Channel
REV: Reverb On/Off
FX: FX Section On / Off
Ext FX: External FX Loop On/Off
Damp: Damping Mode
Tap: Tap Tempo speed
FOOTCONTROLLER FACTORY SETTINGS
Footswitch 1: Clean/Crunch Switch
Footswitch 2: OD-1/OD-2 Switch
Footswitch 3: Tap Tempo Switch
Footswitch 4: Tuner
PROGRAMMING
The footswitch can be programmed to
store front panel switches (Switch Store)
or complete presets (Preset Store).
SWITCH STORE
To assign a front panel switch to a
Footswitch location (1), press and hold
the front panel switch and while held
MG
CLN OD REV FX EXT FX DAMP TAP
Programmable
Footcontroller
- 50 + 50
Note / Preset
4 4
3 3
2 3
down press the Footswitch (1) you wish to
assign it to.
The Digital Display (2) will swirl to show
that the footswitch has been assigned.
You can then release the footswitch and
front panel switch.
PRESET STORE
To assign a preset to a Footswitch (1),
select the required channel and modify
the front panel controls if required, press
and hold the Store switch on the front
panel and while held down, press your
chosen Footswitch (1).
The Digital Display (2) will swirl to show
that the footswitch has been assigned.
You can then release the footswitch and
Store switch.
Footcontroller Presets are independent
of the dedicated Channel presets stored
within the amplifier. This allows you to
create a number of presets based on the
same channel/pre-amp setting.
When either a Channel preset or
Footswitch preset has been altered the
Digital Display (2) will begin to flash.
The footcontroller will flash the relevant
number if a Footswitch preset has been
altered or will flash a "-" if a Channel
preset has been altered.
ENGLISH