Dremel 8200 Original Instructions Manual page 19

o. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
p. Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
q. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
r. Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, sanding band, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a. Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. The operator can control kickback forces, if
proper precautions are taken.
b. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
c. Do not attach a toothed saw blade. Such blades
create frequent kickback and loss of control.
d. Always feed the bit into the material in the same
direction as the cutting edge is exiting from the
material (which is the same direction as the chips
are thrown). Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this feed.
e. When using rotary files, cut-off wheels, high-speed
cutters or tungsten carbide cutters, always have
the work securely clamped. These wheels will grab
if they become slightly canted in the groove, and can
kickback. When a cut-off wheel grabs, the wheel itself
usually breaks. When a rotary file, high-speed cutter
or tungsten carbide cutter grabs, it may jump from the
groove and you could lose control of the tool.
SAFETY WARNINGS SPECIFIC FOR GRINDING AND
ABRASIVE CUTTING-OFF OPERATIONS
a. Use only wheel types that are recommended
for your power tool and only for recommended
applications. For example: do not grind with the
side of a cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
b. For threaded abrasive cones and plugs use only
undamaged wheel mandrels with an unrelieved
shoulder flange that are of correct size and length.
Proper mandrels will reduce the possibility of breakage.
c. Do not "jam" a cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases the
loading and susceptibility to twisting or snagging of
the wheel in the cut and the possibility of kickback or
wheel breakage.
d. Do not position your hand in line with and behind
the rotating wheel. When the wheel, at the point of
operation, is moving away from your hand, the possible
kickback may propel the spinning wheel and the power
tool directly at you.
e. When wheel is pinched, snagged or when
interrupting a cut for any reason, switch off the
power tool and hold the power tool motionless until
the wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur.
Investigate and take corrective action to eliminate the
cause of wheel pinching or snagging.
f. Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece.
g. Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
h. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress
the wires by applying excessive load to the brush.
The wire bristles can easily penetrate light clothing
and/or skin.
b. Allow brushes to run at operating speed for at least
one minute before using them. During this time no
one is to stand in front or in line with the brush.
Loose bristles or wires will be discharged during the
run-in time.
c. Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire
fragments may be discharged at high velocity during
the use of these brushes and may become imbedded
in your skin.
d. Do not exceed 15,000 RPM when using wire
brushes.
DO NOT WORK WITH MATERIALS
WARNING
!
CONTAINING ASBESTOS (ASBESTOS
IS CONSIDERED CARCINOGENIC).
TAKE PROTECTIVE MEASURES
WARNING
!
WHEN DURING WORK DUST CAN
DEVELOP THAT IS HARMFUL TO ONE'S HEALTH,
COMBUSTIBLE OR EXPLOSIVE (some dusts are
considered carcinogenic); wear a dust mask and work
with dust/chip extraction when connectable.
19