DSC TL2803GR Installation Manual page 37

Table 15: External Event Labels
Event [Section] Label
[519] Zone Tamper
[521] Zone Fault
[523] Alternate Communica-
tor Trouble
[525] Module Trouble
[527] Wireless/AML Device
Trouble
[551] Disarmed By
[553] Disarmed
[555] Automatic Disarming
[557] Automatic Arming Can-
celled
[559] Late to Close
[561] Alarm Ocurred After
Arming
[563] Cold Start
[565] Zone Bypassed
[567] Burglary Verified
[569] Alarm Cancelled
[571] Walk Test Begin
[573] System Test
[575] Periodic Test With Trou-
ble
[577] DLS Remote Program-
ming End
[579] SA Remote Program-
ming End
[581] Installer Lead Out
[583] Firmware Update Suc-
cessful
[585] Delinquency
[587] Event buffer 75% full
[592] FTC Restore
[594] Panel Absent Trouble
Restore
[596] Firmware Update
[601] Stay Arm
[603] Night Arm
[605] Activate Command Out-
put 1
[607] Activate Command Out-
put 3
[609] Deactivate Command
Output 1
[611] Deactivate Command
Output 3
[613] Bypass
[615] Status Request
HSPA(3G) Alarm Communicator Installation Manual
Default Label
(Zone Tampe)
(Zone Fault)
(Alternate Communica-
tor Trouble)
(Module Trouble)
(Device Trouble)
(Disarmed By)
(Disarmed)
(Automatic Disarming)
(Automatic Arming Can-
celled)
(Late to Close)
(Alarm Ocurred After
Arming)
(Cold Start)
(Zone Bypassed)
(Burglary Verified)
(Alarm Cancelled)
(Walk Test Begin)
(Test Message)
(Periodic Test With Trou-
ble)
(Remote Programming
End)
(Remote Programming
End)
(Local Programming End)
(Firmware Update Suc-
cessful)
(Delinquency)
(Event Buffer Near Full)
(fail to communicate
restore)
(Panel Communications
Restore)
(Communicator Program-
ming Updated)
(Stay Arm)
(Night Arm)
(Activate Command Out-
put 1)
(Activate Command Out-
put 3)
(Deactivate Command
Output 1)
(Deactivate Command
Output 3)
(Bypass)
(Status Request)
Event [Section] Label
[520] Zone Tamper Restore
[522] Zone Fault Restore
[524] Alternate Communicator
Restore
[526] Module Trouble Restore
[528] Wireless/AML Device
Restore
[552] Armed By
[554] Armed
[556] Automatic Arming
[558] Late to Open
[560] Disarmed After Alarm
[562] Exit Fault
[564] Armed With Zones Bypassed
[566] Zone Unbypassed
[568] Burglary Not Verified
[570] Holdup Verified
[572] Walk Test End
[574] Periodic Test Transmission
[576] DLS Remote Programming
Begin
[578] SA Remote Programming
Begin
[580] Installer Lead In
[582] Firmware Update Begin
[584] Firmware Update Fail
[586] Keypad Lockout
[591] FTC Trouble
[593] Panel Absent Trouble
[595] Module Reprogramming
[600] Module
[602] Away Arm
[604] Disarm
[606] Activate Command Output 2
[608] Activate Command Output 4
[610] Deactivate Command Output 2
[612] Deactivate Command Output 4
[614] Unbypass
[616] Alarm Memory Request
37
Default Label
(Zone Tamper Restore)
(Zone Fault Restore)
(Alternate Communicator
Restore)
(Module Trouble Restore)
(Device Trouble Restore)
(Armed By)
(Armed)
(Automatic Arming )
(Late to Open)
(Disarmed After Alarm)
(Exit Fault)
(Armed With Zones Bypassed)
(Zone Unbypassed)
(Burglary Not Verified)
(Holdup Verified)
(Walk Test End)
(Periodic Test)
(Remote Programming Begin)
(Remote Programming Begin)
(Local Programming Begin)
(Firmware Update Begin)
(Firmware Update Fail)
(Keypad Lockout)
(fail to communicate trouble)
(Panel Communications Trou-
ble)
(Communicator Programming
Updated)
(Module)
(Away Arm)
(Disarm)
(Activate Command Output 2)
(Activate Command Output 4)
(Deactivate Command Output 2)
(Deactivate Command Output 4)
(Unbypass)
(Alarm Memory Request)