Table of Contents
Advertisement
Quick Links
Operator's Manual
3/8 in. (10 mm) CORDLESS DRILL-DRIVER
Vadable Speed / Reversible
Model No.
315.101860 - 14.4 Volt
Save this manual for
future reference
,_
WARNING:
To reducethe risk of injury,
the user must read and understandthe
operator's manual beforeusing this
product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
983000-.409
6-04
Advertisement
Table of Contents
Related Manuals for Sears 315.10186
Summary of Contents for Sears 315.10186
- Page 1 To reducethe risk of injury, the user must read and understandthe operator's manual beforeusing this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman 983000-.409 6-04...
- Page 2 FULL ONE YEAR WARRANTY ON COMPANION CORDLESS 3/8 In. DRILL-DRIVER If this Sears Drill-Driverfails to give complete satisfactionwithin one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES_ and Sears will replace it, free of charge.
-
Page 3: Electrical Safety
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS, Failure to followall instruCtions listedbelow, may resultin electricshock, fire and/or seriouspersonaliniury. SAVE THESE INSTRUCTIONS WORKAREA • Keep your work area clean and well lit. Cluttered benchesand dark areas Inviteaccidents. • Do not operate power tools in explcelve atmo- spheres, such as In the presence of flammable liquids, gee(m, or dust. - Page 4 SERVICE • Tool service must be performed only by qualified repair personnel. Service or maintenancepedormed by unqualifiedpersonnel couldresultin e risk of injury. • Hold tool by insulated gripping surfaces when performing an Operation where the cuffing tool may contact h|dden wiring, Contactwith a "live"wire will also make exposed metal paTtsof the tool"live"and shockthe operator.
- Page 5 WARNINGI READ AND UNDERSTAND ALL INSTRUCTIONS. Failureto followall Instructions listed below, may re.suit in etect_ shock,fire and/or serious personalinjury. • Before using battery charger,read all instructionsand nautlonary markings In this manual, on battery charger, battery,and productusing batteryto prevent misuse of the products and possibleInjuryor damage.
- Page 6 i Important: Some of the followingsymbolsmay be used on this tool. Please studythem and learn their meaning.Proper Interpretationof these symbolswill allowyou to operate the tool better and safer. SYMBOL NAME Volts Amperes Hertz Watt Minutes AlternatingCurrent Direct Current No Load Speed Class II Construction ..Jmln Per Minute...
-
Page 7: Product Specifications
PRODUCTSPECIFICATIONS Chuck ..3/8 in. (10 ram) Keyless Motor ... 14.4 Volt DC Switch ... Vadab[e Speed Gear Train ... 1 Speed No Load Speed ... 0-6501min. KNOW YOUR DRILL-DRIVER See Figure 1, Before attempting to use your ddll-ddver,familiarize yourself with all operating features and safety requirements. - Page 8 KEYLES8 CHUCK CHARQER ASSEMBLY INSTRUCTIONS When unpackingthe tool: • Carefully remove the tool and accassodes from the box. • Make sure that all items listedin the packing list are in- cluded. • Inspect the tool carefully to make sure no breakage or damage occurredduring shipping.
- Page 9 WARNING:Do not allow familiaritywith your drill- df',verto make you careless.Remember that a careless fraction of a secondis sufficientto _nffict severe Injury. CHARGING YOUR DRILL-DRIVER The battery pack for this tool has been shippedIn e low charge condition to prevent passible problems. Therefore, you should charge It at least 6 hourspdor to use.
-
Page 10: Variable Speed
BATrERT PACK DEPRESSLATCHESTO RELEASEBATTERYPACK SWITCH See Figure 5. Your ddi]starts and stops by depressing and releasingthe switch trigger. Release the switchbigger to turn ddll OFF. VARIABLE SPEED See Figure 5. Your ddll has a variable speed feature in the switch. The switch delivem higher speed and torque with increased tdgger pressure. - Page 11 SCREW'DRIVING TORQUE ADJUSTMENT (Driving power of your drill-driver) When using your drill-driverfor varlous driving applica- tions, it becomes necessary to increase or decrease the torque in order to help prevent the possibilityof damaging screw heads, threads, workplace, etc. In general, torque shouldcorrespondto the intensityof the screw diameter.
-
Page 12: Installing Bits
INSTALLING BITS • Place thedirectionof rotationcelector in center position. See Figure 5. This will turnoff the power to your drill. • Open or close the chuck jaws to a point where the opening is slightlylarger than the bit size you intend to use. - Page 13 _1= WARNING: Always wear safety gogglesor safety glasses with side shields when operatingtool, Failure to do so could result in objectsbeing thrown into your eyes, resultingin possibleserious injury, DRILLING See Figure 11. When drillinghard, smooth surfaces, usa a canter punch to mark the desired hole Iocallon.This wff!prevent the ddl[ bit from slippingoff canter as the hole is started.
-
Page 14: Chuck Removal
CHUCK REMOVAL See Figures 12 - 14. • Lockthe swiLch triggerbyplscingthe direction of retation selector in center position.See Figure 5. • Insert a 5/15 inch or larger hex kay Into the chuck of your ddtt and [_ghten the chuck jews sscumly. •... - Page 15 Only the parts shownon parts list, page 17, are intended to be repaired or replaced by the customer. All other parts shouldbe replaced at a Sears Service Center. _1= WARNING: Do not attempt to mod_ this tool or...
-
Page 17: Parts List
COMPANION number in all correspondenceregardingyourCORDLESS DRILL-DRIVER or when orderingrepair parts, The model number will be found on a plate attached to the motor housing. Always mention the model SEE BACK PAGE FOR PARTS ORDERING Number 660120O01 690033022 130122041 140209O23 580013004 983000-409 14.4 VOLT CORDLESS MODEL NO, 315.101860... - Page 18 COMPANION 3/8 In. 14.4VOLT CORDLESS DRILL-DRIVER - MODEL NUMBER 315.101860 %, : 12 _...
- Page 19 COMPANION 3/8 In. 14.4 VOLT CORDLESS CORDLESS DRILL-DRIVER or when orderingrepair parts. The model number will be found on a plate attached to re motor housing.Always mention the model number In all correspondenceregarding your | PART NUMBER 6620501 * SCREW (M3 X 14 mm)...
-
Page 20: Wiring Diagram
COMPANION 3/8 In. 14.4 VOLT CORDLESS DRILL-DRIVER - MODEL NUMBER 315.101860 BLUE LEAD RED LEAD HEAT SINK BLACK LEAD BLACK LEAD BLACK LEAD WIRING DIAGRAM... - Page 21 Ioca_on of your nearest Sears Parts & Repair Center. Call anytime, day or night (U.S.A. only) To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced by Sears: 1-800-827-6655 (U.S,A.) Para pedir servicio de reparacibn...