Battery Charging; Assembly Instructions - Schumacher SE-3522 Owner's Manual

K.
CHARGER MUST BE ASSEMBLED BEFORE USING.
1. Before charging any battery, make sure the electrolyte (bat-
tery liquid) in each cell is at correct level.
2 Set Switch #2 to the "OFF position.
3. If the battery is being charged inside the vehicle, use connec-
tion procedures outlined in Section F. Should the battery be
removed from the vehicle, follow the instruction in Section D,
step 6 and Section G. Plug the power cord into the AC outlet.
4. Set the charge rate switch to the desired charge position.
See Charge Rate Charts and Section H.
BATTERY SIZE/RATING
Motorcycle, Garden
SMALL
BATTERIES
Tractor, etc.
200 - 315 CCA
CAR/TRUCKS 315 - 550 CCA
550 - 875 CCA
MARINE/
DEEP CYCLE
L.
Wheel Charger Assembly Instructions: (Instrucciones De Armado)
NOTE: Charger must be assembled before operating (Ante de la operación la unidad debe estar armada)
Parts (Piezas)
(4) 10-32 screws (tornillos de corte rosca 10-32)
(2) 1/4-20 screws (tornillo de corte rosca 1/4-20)
(2) wheels(ruedas)
(2) axle caps (tapas del eje)
(2) axle brackets (soportes de eje)
(1) handle (mango)
(1) mounting foot (pedestal de montaje)
(1) axle (del eje)
First place the charger on it side.
Next mount the mounting foot FIG. A with (2) 1/4-20 screws.
Next pound the axle firmly into an axle cap using a hammer FIG. B.
Next slide the wheels onto the axle, hubs must face in, FIG. C.
Next pound the other axle cap onto the other end of the axle.
Next place the axle assembly onto the bottom of the charger as shown in FIG. C.
Mount the axle to the bottom of the charger using (2) 10-32 screws as shown in FIG. D.
Next turn the charger right side up onto its foot and wheels.
Remove the (2) top screws from each side of the charger, line up the handle and reinstall the screws FIG. E.
Primero coloque el cargador de lado.
A continuación monte el pedestal FIG. A con (2) tornillos 1/4-20.
A continuación golpee firmemente el eje dentro de la tapa del eje usando un martillo, FIG. B.
A continuación deslice las ruedas dentro del eje; los cubos deben estar orientados hacia adentro, FIG. C.
A continuación golpee la otra tapa del eje dentro del otro extreme del eje.
A continuación coloque el conjunto del eje dentro del fondo del cargador según se muestra en la FIG. C.
Monte el eje en el fondo del cargador usando los dos tornillo de corte de rosca 10-32 según se muestra en la FIG. D.
A continuación gire el cargador de la batería con el lado derecho hacia arriba sobre su pedestal y ruedas.
Saque los dos tornillos superiores de cada lado del cargador; alinee el mango y reinstale los tornillo. FIG. E.

BATTERY CHARGING

CHARGE RATE*/
CHARGING TIME - HOURS**
2 AMP 35 AMP
6 - 12 AH 1.5 to 3
NR
12 - 32 AH 3 to 8
40 - 60 RC 11 to 15 .5 to .75
60 - 85 RC 15 to 18 .75 to 1
85 - 125 RC 18 to 25 1 to 1.5
55 MC 15 NR
80 MC 19 1.75
105 MC 23 2

ASSEMBLY INSTRUCTIONS

Tools necessary (Herramientas Necesarias)
5/16" wrench
3/8" wrench
Hammer
Screwdriver
NOTE: These battery chargers are not automatic and can
overcharge a battery if permitted to operate for ex-
tended periods of time. Monitor the charging of-
ten.
Also, your charger may exhibit a noise (buzzing)
during charging. Laminations of the transformer
tend to vibrate. This is normal...continue to charge
the battery.
*Charge Rates for this model are listed on the
front panel.
**Based on battery at 50% charge.
AH Ampere Hours
NR Not Recommended
CCA Cold Cranking Amps
RC Reserve Capacity
MC Marine Capacity
(Llave de 5/16")
(Llave de 3/8")
(Martillo)
(Destornillador)
Fig. A
5
HUBS MUST
FACE IN
Fig. C
AXLE BRACKET
Fig. D
Fig. E
Fig. B
AXLE CAP