Savin 2235 Operator's Manual

Savin corporation copier / printer operator's manual
Hide thumbs Also See for 2235:

Advertisement

AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM
2535/2545/2535p/2545p
3502/4502/3502p/4502p
2235/2245/2335/2345
Series
Operator Manual
Copy Reference
Read this manual carefully before you use this product and keep it handy for future
reference.
For safety, please follow the instructions in this manual.
Zdsh000j.eps

Advertisement

Table of Contents
loading

Summary of Contents for Savin 2235

  • Page 1 AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM 2535/2545/2535p/2545p 3502/4502/3502p/4502p 2235/2245/2335/2345 Series Operator Manual Copy Reference Zdsh000j.eps Read this manual carefully before you use this product and keep it handy for future reference. For safety, please follow the instructions in this manual.
  • Page 2: Machine Types

    Two kinds of size notation are employed in this manual. With this machine refer to the inch version. For good copy quality, Savin recommends that you use genuine toner. Savin shall not be responsible for any damage or expense that might result from the use of parts other than genuine parts in your office product.
  • Page 3 7. If you cannot correct the problem, please contact the SAVIN CORPORATION at 1-203-967- 5000 for repair and warranty information. If it is causing harm to the telephone network, the tele- phone company may request you to disconnect the equipment from the network until the prob- lem is resolved.
  • Page 4: Safety Information

    AdonisC2_ENcopy122F_FM.book Page i Thursday, February 15, 2001 3:23 PM Safety Information When using your equipment, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
  • Page 5 AdonisC2_ENcopy122F_FM.book Page ii Thursday, February 15, 2001 3:23 PM R CAUTION: • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment.
  • Page 6 AdonisC2_ENcopy122F_FM.book Page iii Thursday, February 15, 2001 3:23 PM How to Read this Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the in- structions under this symbol.
  • Page 7: Table Of Contents

    AdonisC2_ENcopy122F_FM.book Page iv Thursday, February 15, 2001 3:23 PM TABLE OF CONTENTS Machine Types... 1 What You Can Do with This Machine (Copy Mode)... 2 Guide To Components ... 5 Output Tray Guide... 7 Options ... 8 Control Panel ... 9 Display Panel ...
  • Page 8 AdonisC2_ENcopy122F_FM.book Page v Thursday, February 15, 2001 3:23 PM Basic Functions... 37 Adjusting Copy Image Density ... 37 Selecting Original Type Setting... 39 Selecting Copy Paper ... 40 Auto Reduce/Enlarge ... 43 Sort/Stack/Staple ... 44 Sort... 45 Stack ... 48 Staple ...
  • Page 9 AdonisC2_ENcopy122F_FM.book Page vi Thursday, February 15, 2001 3:23 PM 1 Sided 8 Pages → Combine 2 Side... 92 1 Sided 16 Pages → Combine 2 Side... 93 2 Sided 2 Pages → Combine 1 Side... 94 2 Sided 4 Pages → Combine 1 Side... 95 2 Sided 8 Pages →...
  • Page 10 AdonisC2_ENcopy122F_FM.book Page vii Thursday, February 15, 2001 3:23 PM 3. Document Server Overview... 149 Process ... 150 Features and Benefits ... 151 On Demand Printing... 151 File Merge Printing ... 152 Facsimile Resend... 154 Operation from a Computer ... 154 Scanning Originals...
  • Page 11 AdonisC2_ENcopy122F_FM.book Page viii Thursday, February 15, 2001 3:23 PM d Adding Staples ... 198 1000-Sheet Finisher... 198 2 Tray Finisher ... 200 e Removing Jammed Staples... 202 1000-Sheet Finisher... 202 2 Tray Finisher ... 204 y Removing Punch Waste... 206 5.
  • Page 12 AdonisC2_ENcopy122F_FM.book Page ix Thursday, February 15, 2001 3:23 PM 6. REMARKS Do's And Don'ts... 235 Where to Put Your Machine... 236 Machine Environment ... 236 Moving... 236 Power Connection... 237 Access to the Machine ... 237 Maintaining Your Machine ... 238 Cleaning the Exposure Glass...
  • Page 13 AdonisC2_ENcopy122F_FM.book Page x Thursday, February 15, 2001 3:23 PM...
  • Page 14: Machine Types

    AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM Machine Types This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover. Copy speed Type 1 Type 2 35 copies/minute (A4K, 8 "...
  • Page 15: What You Can Do With This Machine (Copy Mode)

    AdonisC2_ENcopy122F_FM.book Page 2 Thursday, February 15, 2001 3:23 PM What You Can Do with This Machine (Copy Mode) Positive/Negative...
  • Page 16 AdonisC2_ENcopy122F_FM.book Page 3 Thursday, February 15, 2001 3:23 PM Document Server *1 Optional 2 Tray finisher is reguired. *2 Optional Bridge unit and optional finisher are reguired. Series/Book Front & Back 1 Sided & Booklet 2 Sided & Booklet 2 Sided & Magazine 1 Sided &...
  • Page 17 AdonisC2_ENcopy122F_FM.book Page 4 Thursday, February 15, 2001 3:23 PM “Selecting Original Type Setting” ⇒ ⇒ ⇒ ⇒ P.39 “Adjusting Copy Image Density” ⇒ ⇒ ⇒ ⇒ P.37 “Setting Special Originals” ⇒ ⇒ ⇒ ⇒ P.33 “Image Repeat” ⇒ ⇒ ⇒ ⇒ P.112 “Double Copies”...
  • Page 18: Guide To Components

    AdonisC2_ENcopy122F_FM.book Page 5 Thursday, February 15, 2001 3:23 PM Guide To Components Document Feeder (ADF) The document feeder automatically feeds a stack of originals one by one. Exposure glass Place originals here face down for copy- ing. ⇒ P.19 “Originals” Internal tray Copied paper is delivered here face down.
  • Page 19 AdonisC2_ENcopy122F_FM.book Page 6 Thursday, February 15, 2001 3:23 PM Bypass tray Use when copying onto OHP transparen- cies, adhesive labels, translucent paper, postcards, and custom size paper. Ventilation hole Prevents overheating. Do not obstruct the ventilation hole by placing an object near it or leaning an object against it.
  • Page 20: Output Tray Guide

    AdonisC2_ENcopy122F_FM.book Page 7 Thursday, February 15, 2001 3:23 PM Output Tray Guide When copying onto OHP transparencies and translucent paper, raise the guide. This prevents copies from being curled when delivered. ❖ ❖ ❖ ❖ To copy onto normal paper and thick paper Slide the guide in the direction of the arrow.
  • Page 21: Options

    AdonisC2_ENcopy122F_FM.book Page 8 Thursday, February 15, 2001 3:23 PM Options 1000-Sheet Finisher Sorts, stacks, and staples copies. External tray If you selected this as the output tray, copied paper is delivered here face down. Platen cover Lower this cover over originals for copy- ing.
  • Page 22: Control Panel

    AdonisC2_ENcopy122F_FM.book Page 9 Thursday, February 15, 2001 3:23 PM Control Panel Screen Contrast knob Adjusts the brightness of the display pan- Indicators These indicators show errors or the status of the machine. ⇒ P.169 “Troubleshoot- ing”. { { { { User Tools/Counter} } } } key •...
  • Page 23 AdonisC2_ENcopy122F_FM.book Page 10 Thursday, February 15, 2001 3:23 PM { { { { Clear/Stop} } } } key • Clear Press to delete a number entered. • Stop Press to stop a copy job in progress. { { { { #} } } } key Press to enter a value.
  • Page 24: Display Panel

    AdonisC2_ENcopy122F_FM.book Page 11 Thursday, February 15, 2001 3:23 PM Display Panel The display panel shows the status of the machine, error messages and function menus. Important ❒ Do not apply a strong shock or force of about 30 N (about 3 kgf) or more to the display panel.
  • Page 25 AdonisC2_ENcopy122F_FM.book Page 12 Thursday, February 15, 2001 3:23 PM Displays the contents of the Shortcut keys. You can register fre- quently used functions in these keys. ⇒ ⇒ ⇒ ⇒ “Copy Function Key F1-F5” in P.217 “General Features ❖ ❖ ❖ ❖ Function menu Items you can select.
  • Page 26: Function List Based On Options

    AdonisC2_ENcopy122F_FM.book Page 13 Thursday, February 15, 2001 3:23 PM Function List Based on Options The functions that are available to you depend on your machine configuration and which options you have. See the table below. ❍…Available ×…Not available Mixed Sizes Mode Custom Size Originals Original Orientation (Standard Orientation)
  • Page 27 AdonisC2_ENcopy122F_FM.book Page 14 Thursday, February 15, 2001 3:23 PM Copying Book Originals Image Repeat Double Copies Centering Positive/Negative Border Erase/Center Erase Margin Adjustment Background Numbering Preset Stamp User Stamp Date Stamp/Page Numbering Cover/Front/Back Cover/Slip Sheet Sort Shift Sort Rotate Sort Shift Stack Staple Punch...
  • Page 28: Basics

    AdonisC2_ENcopy122F_FM.book Page 15 Thursday, February 15, 2001 3:23 PM Turning On the Power To turn the machine on, press the op- eration switch. Note ❒ This machine automatically enters Energy Saver mode or turns itself off if you do not use the machine for a while.
  • Page 29: Turning On The Power

    AdonisC2_ENcopy122F_FM.book Page 16 Thursday, February 15, 2001 3:23 PM Basics Turning On the Power Press the operation switch to make the On indicator goes on. The display panel will come on. Note ❒ If the power is not turned on when the operation switch is pressed, check if the main pow- er switch is on.
  • Page 30 AdonisC2_ENcopy122F_FM.book Page 17 Thursday, February 15, 2001 3:23 PM Turning Off the Main Power Make sure that the On indicator goes off. Turn off the main power switch to make sure the indicator goes off. Important ❒ Do not turn off the main power switch when the indicator goes on or blink Hard Disk or Mem- ory might be broken.
  • Page 31: Changing Modes

    AdonisC2_ENcopy122F_FM.book Page 18 Thursday, February 15, 2001 3:23 PM Basics Changing Modes You can use this machine not only as a copier, but also as a fax, printer, docu- ment server and scanner as well. Press the {Copy}, {Facsimile}, {Printer}, {Scan- ner} or {Document Server} key to use that function.
  • Page 32: Originals

    AdonisC2_ENcopy122F_FM.book Page 19 Thursday, February 15, 2001 3:23 PM Originals Sizes and Weights of Recommended Originals ❖ ❖ ❖ ❖ Metric version Where Original Is Set Original Size Exposure glass Up to A3 Document feeder 1-sided originals: A3L – B6KL 2-sided originals: A3L –...
  • Page 33: Sizes Detectable By The Auto Paper Select

    AdonisC2_ENcopy122F_FM.book Page 20 Thursday, February 15, 2001 3:23 PM Basics • Originals with indexes, tags, or other projecting parts • Sticky originals such as translucent paper • Thin originals that have low stiffness • Thick originals such as postcards • Originals of inappropriate weight •...
  • Page 34: Missing Image Area

    AdonisC2_ENcopy122F_FM.book Page 21 Thursday, February 15, 2001 3:23 PM Missing Image Area ❖ ❖ ❖ ❖ Exposure glass Reference position Horizontal size Maximum Scanning area (297x420mm) 11"x17" (279x432mm) ❖ ❖ ❖ ❖ Document feeder Limitation ❒ Even if you correctly set originals in the document feeder or on the exposure glass, 3mm (0.1") margins on all four sides of the original might not be copied.
  • Page 35: Copy Paper

    AdonisC2_ENcopy122F_FM.book Page 22 Thursday, February 15, 2001 3:23 PM Basics Copy Paper Recommended Paper Sizes and Types The following limitations apply to each tray: Tray 1 Tray 2 Metric Version Inch Version A3L, B4L, <A3L, B4L>, A4KL, B5KL, A4KL, <A5L>, <B5KL, A5L>, <11"...
  • Page 36 AdonisC2_ENcopy122F_FM.book Page 23 Thursday, February 15, 2001 3:23 PM Tray 3 A3L, B4L, A4KL, B5KL, Tray 4 A5L, 11" × 17"L, OPTION 8" × 13"L, 11" × 14"L, 8" × 10 Bypass Standard A3L, B4L, A4L, *2 *3 *4 Tray Size B5L, A5L, PostcardL,...
  • Page 37 AdonisC2_ENcopy122F_FM.book Page 24 Thursday, February 15, 2001 3:23 PM Basics Important ❒ If you use damp or curled paper, a misfeed might occur. In this case, try turn- ing over the paper stack in the paper tray. If there is no improvement, change to paper with less curl.
  • Page 38: Direction-Fixed Paper Or 2-Sided Paper

    AdonisC2_ENcopy122F_FM.book Page 25 Thursday, February 15, 2001 3:23 PM Copy Paper Direction-fixed paper or 2-sided paper The direction-fixed (top to bottom) or 2-sided paper (letterhead paper, punched paper, or copied paper, e.g.) might not be printed correctly depending on how the originals and paper are set in place.
  • Page 39: Non-Recommended Paper

    AdonisC2_ENcopy122F_FM.book Page 26 Thursday, February 15, 2001 3:23 PM Basics Non-recommended Paper R CAUTION: • Do not use aluminum foil, carbon paper, or similar conductive paper to avoid a fire or equipment failure. Important ❒ Do not use any of the following kinds of paper or a fault might occur. •...
  • Page 40: Toner

    AdonisC2_ENcopy122F_FM.book Page 27 Thursday, February 15, 2001 3:23 PM Toner Handling Toner R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ig- nite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: •...
  • Page 41 AdonisC2_ENcopy122F_FM.book Page 28 Thursday, February 15, 2001 3:23 PM Basics...
  • Page 42: Copying

    AdonisC2_ENcopy122F_FM.book Page 29 Thursday, February 15, 2001 3:23 PM Basic Procedure Make sure that the machine is in Copy mode. If the machine is not in Copy mode, press the {Copy} key. When the machine is set for the user code, enter the user code with the number keys and then press the { { { { #} } } } key.
  • Page 43: Auto Off

    AdonisC2_ENcopy122F_FM.book Page 30 Thursday, February 15, 2001 3:23 PM Copying - System Reset The machine returns to its initial con- dition automatically when your job is finished, after a certain period of time. This function is called “System Reset”. Note ❒...
  • Page 44: Setting Originals

    AdonisC2_ENcopy122F_FM.book Page 31 Thursday, February 15, 2001 3:23 PM Setting Originals Limitation ❒ Set originals after correction fluid and ink has completely dried. Not taking this precaution could mark the exposure glass and cause marks to be copied. Note ❒ Basically originals aligned to the rear left corner.
  • Page 45: Setting Originals In The Document Feeder

    AdonisC2_ENcopy122F_FM.book Page 32 Thursday, February 15, 2001 3:23 PM Copying Setting Originals in the Document Feeder Note ❒ The last page should be on the bot- tom. ❒ Do not stack originals beyond the limit mark on the side fence of the document feeder.
  • Page 46: Setting Special Originals

    AdonisC2_ENcopy122F_FM.book Page 33 Thursday, February 15, 2001 3:23 PM 90° Turn When you want to copy A3K, B4K or 11" × 17"K size originals, set your original in the landscape orientation and then press the key. The machine rotates the original image and you can make copies as you wish.
  • Page 47: Mixed Size Mode

    AdonisC2_ENcopy122F_FM.book Page 34 Thursday, February 15, 2001 3:23 PM Copying Press the [OK] key. Set your originals, then press the { { { { Start} } } } key. After all the previously set origi- nals are fed, set the next originals. The second and subsequent origi- nals can be fed automatically with- out pressing the {Start} key.
  • Page 48: Setting Custom Size Originals

    AdonisC2_ENcopy122F_FM.book Page 35 Thursday, February 15, 2001 3:23 PM Press the [Special Original] key. Press the [Mixed size] key. Press the [OK] key. Align the rear and left edges of the originals as shown in the il- lustration. 1: Set into the document feeder. 2: Vertical size Adjust the guide to the widest original size.
  • Page 49 AdonisC2_ENcopy122F_FM.book Page 36 Thursday, February 15, 2001 3:23 PM Copying Note ❒ If you make a mistake, press the [Clear] or {Clear/Stop} key, and then enter the value again. Enter the vertical size of the origi- nal with the Number keys, then press the [#] key.
  • Page 50: Basic Functions

    AdonisC2_ENcopy122F_FM.book Page 37 Thursday, February 15, 2001 3:23 PM Basic Functions The following basic functions are ex- plained in this section. ❖ ❖ ❖ ❖ Adjusting Copy Image Density Auto and Manual Image Density ❖ ❖ ❖ ❖ Selecting Original Type Setting Text, Text·Photo, Photo, Pale, Gen- eration Copy ❖...
  • Page 51 AdonisC2_ENcopy122F_FM.book Page 38 Thursday, February 15, 2001 3:23 PM Copying Auto Image Density Make sure that the [Auto Image Den- sity] key is selected. Note ❒ If the [Auto Image Density] key is not selected, press the [Auto Im- age Density] key. ❒...
  • Page 52: Selecting Original Type Setting

    AdonisC2_ENcopy122F_FM.book Page 39 Thursday, February 15, 2001 3:23 PM Selecting Original Type Setting Select one of the following types to match your originals: ❖ ❖ ❖ ❖ Text Select this mode when your origi- nals contain only letters (no pic- tures).
  • Page 53: Selecting Copy Paper

    AdonisC2_ENcopy122F_FM.book Page 40 Thursday, February 15, 2001 3:23 PM Copying Selecting Copy Paper There are two ways to select copy paper: ❖ ❖ ❖ ❖ Auto Paper Select The machine selects a suitable size of copy paper automatically based on the original size and the reproduction ratio.
  • Page 54 AdonisC2_ENcopy122F_FM.book Page 41 Thursday, February 15, 2001 3:23 PM Auto Paper Select Make sure that the [Auto Paper Select] key is selected. Note ❒ If the [Auto Paper Select] key is not selected, press the [Auto Paper Select] key. ❒ If you do not wish to set any other functions, press the {Start} key to start copying.
  • Page 55 AdonisC2_ENcopy122F_FM.book Page 42 Thursday, February 15, 2001 3:23 PM Copying - Rotated copy If the direction in which your original is set (landscape or portrait) is different from that of the paper you are copying onto, this function rotates the original im- age by 90°...
  • Page 56: Auto Reduce/Enlarge

    AdonisC2_ENcopy122F_FM.book Page 43 Thursday, February 15, 2001 3:23 PM Auto Reduce/Enlarge The machine can choose an appropri- ate reproduction ratio based on the paper and original sizes you select. Limitation ❒ You cannot use the bypass tray with this function. Note ❒...
  • Page 57: Sort/Stack/Staple

    AdonisC2_ENcopy122F_FM.book Page 44 Thursday, February 15, 2001 3:23 PM Copying Sort/Stack/Staple The machine can scan your originals into memory and automatically sort the copies. ❖ ❖ ❖ ❖ Sort • Sort • Rotate Sort • Shift sort (the optional finisher and the optional Bridge unit are equired) ❖...
  • Page 58: Sort

    AdonisC2_ENcopy122F_FM.book Page 45 Thursday, February 15, 2001 3:23 PM ❖ ❖ ❖ ❖ Inch version " × 14"L or larger: 250 Internal • 8 tray sheets (20 lb.) " × 11K or smaller: 500 • 8 sheets (20 lb.) Internal 125 sheets (20 lb.) tray 2 (1 bin...
  • Page 59 AdonisC2_ENcopy122F_FM.book Page 46 Thursday, February 15, 2001 3:23 PM Copying ❒ The paper sizes that can be used in the Rotate Sort function are as follows: Metric version A4KL, B5KL Inch version ❒ To use the Rotate Sort function, two paper trays identical in size and different in direction (KL) are required.
  • Page 60 AdonisC2_ENcopy122F_FM.book Page 47 Thursday, February 15, 2001 3:23 PM ❖ ❖ ❖ ❖ When the 2 Tray Finisher is installed Note ❒ When the optional finisher is in- stalled, use the User Tools to dis- play [Rotate Sort]. ⇒ “Select Stack Function”...
  • Page 61: Stack

    AdonisC2_ENcopy122F_FM.book Page 48 Thursday, February 15, 2001 3:23 PM Copying Stack Copies can be assembled with each page set. ❖ ❖ ❖ ❖ Shift Stack • 1000-Sheet/2 Tray-Sheet Finisher This function groups copies of each page in a multi-page origi- nal together.
  • Page 62 AdonisC2_ENcopy122F_FM.book Page 49 Thursday, February 15, 2001 3:23 PM B Set the next original. When it is placed on the exposure glass, press the { { { { Start} } } } key. Note ❒ Set the original in the same direction as the first one.
  • Page 63: Staple

    AdonisC2_ENcopy122F_FM.book Page 50 Thursday, February 15, 2001 3:23 PM Copying Staple The optional finisher and the bridge unit are required to use this function. Each copy set can be stapled together. Limitation ❒ You cannot use the following paper in this function: •...
  • Page 64 AdonisC2_ENcopy122F_FM.book Page 51 Thursday, February 15, 2001 3:23 PM ❖ ❖ ❖ ❖ Inch version With 1000-Sheet Finisher 11" × 17"L, 8 Paper size " × 11"KL " × 11" or smaller: 30 sheets Stapler • 8 capacity (20 lb.) "...
  • Page 65 AdonisC2_ENcopy122F_FM.book Page 52 Thursday, February 15, 2001 3:23 PM Copying ❖ ❖ ❖ ❖ 1000-sheet Finisher When your machine is equipped with the 1000-sheet finisher, the stapling po- sition will be fixed to “Top Slant”. STAPLEBE Note ❒ Original images are not rotated. ❖...
  • Page 66 AdonisC2_ENcopy122F_FM.book Page 53 Thursday, February 15, 2001 3:23 PM STAPLEDE STAPLEEE Available staple positions except A3, B4, size of paper. Note ❒ You cannot change stapling positions during copying. ❒ When the original image is rotated, the stapling direction turns by 90°. ❒...
  • Page 67 AdonisC2_ENcopy122F_FM.book Page 54 Thursday, February 15, 2001 3:23 PM Copying ❖ ❖ ❖ ❖ 2 Tray Finisher Note ❒ When you select the stapling position, Sort mode is automatically selected. Reference ⇒ P.51 “Stapling position and original setting” Enter the number of copy sets with the number keys. Note ❒...
  • Page 68: To Stop Scanning Temporarily

    AdonisC2_ENcopy122F_FM.book Page 55 Thursday, February 15, 2001 3:23 PM To Stop Scanning Temporarily When you are using the Sort, Stack, or Staple function, the originals are scanned into memory. Press the { { { { Clear/Stop} } } } key to stop originals from being scanned into memory.
  • Page 69: Punch

    AdonisC2_ENcopy122F_FM.book Page 56 Thursday, February 15, 2001 3:23 PM Copying Punch The optional 2 tray finisher and the bridge unit are required to use this function. This function is used to make punch holes in copies. ❖ ❖ ❖ ❖ 2 holes ❖...
  • Page 70 AdonisC2_ENcopy122F_FM.book Page 57 Thursday, February 15, 2001 3:23 PM Note ❒ When using Punch and Combine, Double Copies, or Auto Reduce/Enlarge, the message "Blank part will appear. Check orientation." may appear because of the orientation of the original and the copy paper. If this occurs, change the orientation of the copy paper.
  • Page 71 AdonisC2_ENcopy122F_FM.book Page 58 Thursday, February 15, 2001 3:23 PM Copying Direction in which Original is Set Exposure glass 4 holes ❒ Punchable paper sizes are as follows: With 2 Tray Finisher Punch kit type 2 & 4 holes type 4 holes type 2 &...
  • Page 72 AdonisC2_ENcopy122F_FM.book Page 59 Thursday, February 15, 2001 3:23 PM Enter the number of copy sets with the number keys. Note ❒ To change the entered number, press the {Clear/Stop} key. ❒ If you wish to use the Sort function, press the [Sort] key. Set your originals, then press the { { { { Start} } } } key.
  • Page 73: Copying From The Bypass Tray

    AdonisC2_ENcopy122F_FM.book Page 60 Thursday, February 15, 2001 3:23 PM Copying Copying from the Bypass Tray Use the bypass tray to copy onto OHP transparencies, adhesive labels, trans- lucent paper, postcards, and copy pa- per that cannot be set in the paper tray.
  • Page 74 AdonisC2_ENcopy122F_FM.book Page 61 Thursday, February 15, 2001 3:23 PM ❒ If the beeper is turned off, light- ly insert the copy paper until it stops. Refer to the System Set- tings manual. ❒ When the document feeder is open, set the direction of the copy paper to L.
  • Page 75 AdonisC2_ENcopy122F_FM.book Page 62 Thursday, February 15, 2001 3:23 PM Copying B Press the [Custom Size] key. C Press the [Vertical mm] key and enter the vertical size of the pa- per with the number keys, then press the [#] key. Note ❒...
  • Page 76: When Copying Onto Ohp Transparencies Or Thick Paper

    AdonisC2_ENcopy122F_FM.book Page 63 Thursday, February 15, 2001 3:23 PM When Copying onto OHP Transparencies or Thick Paper To make copies onto OHP transpar- encies or thick paper, you need to specify the paper type. Note ❒ Select [Thick Paper] if the paper weight is more than 128g/m Open the bypass tray, and adjust the guides to the paper size.
  • Page 77: Programs

    AdonisC2_ENcopy122F_FM.book Page 64 Thursday, February 15, 2001 3:23 PM Copying Programs You can store frequently used copy job settings in machine memory, and recall them for future use. ❖ ❖ ❖ ❖ Storing Your Settings You can store your settings you frequently use.
  • Page 78: Deleting A Program

    AdonisC2_ENcopy122F_FM.book Page 65 Thursday, February 15, 2001 3:23 PM Note ❒ If you do not wish to enter the program name, go to step F. ❒ You can register up to 40 char- acters. ❒ To change the name entered, press the [Backspace], [Delete] or {Clear/Stop} key and enter new letters.
  • Page 79: Recalling A Program

    AdonisC2_ENcopy122F_FM.book Page 66 Thursday, February 15, 2001 3:23 PM Copying Recalling a Program Press the { { { { Program} } } } key. Press the [Recall] key. Press the program number you want to recall. The stored settings are displayed. Note ❒...
  • Page 80: Job Preset

    AdonisC2_ENcopy122F_FM.book Page 67 Thursday, February 15, 2001 3:23 PM Job Preset If a long copy job is in progress and you do not wish to wait for it to finish, you can use this function to set up the next one copy job in advance. When the current copy job is finished, your copy job will be started automatically.
  • Page 81: Other Functions

    AdonisC2_ENcopy122F_FM.book Page 68 Thursday, February 15, 2001 3:23 PM Copying Other Functions Energy Saver Mode If you do not operate the machine for a certain period after copying, or when you press the {Energy Saver} key, the display disappears and the machine enters Energy Saver mode.
  • Page 82: Original Beeper

    AdonisC2_ENcopy122F_FM.book Page 69 Thursday, February 15, 2001 3:23 PM To interrupt copying after all originals have been fed Press the { { { { Interrupt} } } } key. The Interrupt indicator goes on. Note ❒ Copying will not stop yet. Set your original.
  • Page 83: Changing The Number Of Sets

    AdonisC2_ENcopy122F_FM.book Page 70 Thursday, February 15, 2001 3:23 PM Copying Changing the Number of Sets You can change the number of copy sets during copying. Limitation ❒ This function can be used only when the Sort function has been turned on. Press the { { { { Clear/Stop} } } } key when “Copying”...
  • Page 84: Preset Reduce/Enlarge

    AdonisC2_ENcopy122F_FM.book Page 71 Thursday, February 15, 2001 3:23 PM Preset Reduce/Enlarge You can select a preset ratio for copy- ing. Note ❒ You can select one of 12 preset ra- tios (5 enlargement ratios, 7 reduc- tion ratios). ❒ Use “Create Margin” to reduce the image to 93% of its original size with the centre as reference.
  • Page 85: Create Margin Mode

    AdonisC2_ENcopy122F_FM.book Page 72 Thursday, February 15, 2001 3:23 PM Copying Original → → → → Copy Ratio (%) paper size 11" × 15"→8 11" 11" × 17"→8 11" 11" × 17"→5 50 (reduce area by Press the [Reduce/Enlarge] key. Note ❒...
  • Page 86: Zoom

    AdonisC2_ENcopy122F_FM.book Page 73 Thursday, February 15, 2001 3:23 PM Zoom You can change the reproduction ra- tio in 1% steps. Note ❒ The following ratios can be select- • Metric version: 25 – 400% • Inch version: 25 – 400% ❒...
  • Page 87 AdonisC2_ENcopy122F_FM.book Page 74 Thursday, February 15, 2001 3:23 PM Copying B Enter the desired ratio with the number keys. Note ❒ To change the ratio entered, press the [Clear] or {Clear/ Stop} key and enter the new ratio. C Press the [#] key. D Press the [OK] key.
  • Page 88: Size Magnification

    AdonisC2_ENcopy122F_FM.book Page 75 Thursday, February 15, 2001 3:23 PM Size Magnification This function calculates an enlarge- ment or reduction ratio based upon the lengths of the original and copy. Preparation Measure and specify the lengths of the original and copy by compar- ing “A”...
  • Page 89 AdonisC2_ENcopy122F_FM.book Page 76 Thursday, February 15, 2001 3:23 PM Copying Enter the length of the copy with the number keys and press the [#] key. Note ❒ To change the length entered, press the [Clear] or {Clear/Stop} key and enter the new length. ❒...

Table of Contents