Universal Remote Control UR2-DTA Operating Instructions

Operating Instructions For 1
Introduction
UR2-DTA
UR2-DTA
The is designed to
operate the S/A, Pace Micro,
Motorola and IPTV set tops, plus
DTA Remote Control the majority of TV equipment on
the market as shown below.
DTA : DTA boxs, IPTV set tops
TV : Televisions
2
Replacing Batteries
Before you program or operate the
remote control, you must install two new
AA alkaline batteries.
STEP1 Remove the battery compart-
ment cover on the back of your
remote control.
STEP2 Check battery polarity carefully,
and install the batteries as
shown in the illustration below.
STEP3 Replace the battery compart-
ment cover.
3
Operations
Volume Default: TV volume and mute
through The TV, with the option of con-
trolling volume and mute through the
Cable. Refer to Section F For program-
Universal Remote Control, Inc.
ming the volume and mute through
www.universalremote.com
your Cable.
OCE-0089A REV 29 (10/22/18)
4
Button Functions
5
Programming the Remote Control
There are three ways you can program your remote:
* Quick Set-Up Method
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
The Quick Set-Up Method is a unique new feature that enables the fastest and
easiest set-up by using one-digit codes for up to 10 major brands for each compo-
nent.
The Pre-Programmed Code Method allows you to setup all the buttons at once by
entering 3-digit code numbers that correspond to a particular Component's manu-
facturer/brand, so it's the fastest and easiest of the two methods. (Code Tables
are on the backside of this Instruction Sheet.) The Auto-Search Method scans
through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTE!
TV
Quick Number Manufacturer/Brand
This pertains to all programming steps.
0 SANYO
When you are in setup mode, a compo-
1 SONY
nent LED will light for 20 seconds.If you do
2 SAMSUNG
not press a button within 20 seconds, the
3 LG
LED light will turn off and exit setup mode
4 TOSHIBA
and you will need to start over.
5 PANASONIC
6 PHILIPS
A. Quick Set-Up Method
7 HITACHI
8 SHARP
STEP1 Turn on the component you
9 VIZIO
want to program. To program
your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key
C. Pre-Programmed 3-Digit Code
for 5 seconds until the POWER
Method
LED will blink once and stays
on. Continue to hold the
STEP1 Turn on the Component you want
[DEVICE] key and press the
to program(TV, DTA).
number key assigned to your
STEP2 Press the [COMPONENT] button
brand in the Quick Set-up Code
(TV or DTA) to be programmed
Table and release both
and OK button simultaneously
[DEVICE] key and the number
for 3 seconds. The POWER LED
key to save the code. The
light will turn on for 20 seconds
POWER LED will blink twice to
indicating the unit is ready to be
confirm that the code is stored.
programmed.
STEP3 Point the remote control at the
STEP3 Point the remote control toward
component.
the Component and enter the 3-
STEP4 Press the power button. If it
digit code number assigned to
turns off, it is programmed for
your brand.
your component. If it does not
*Note : If the 3-digit code number you just
turn off, use the Pre-
entered is correct, the Component
Programmed 3-Digit code
will turn Off. If it did not turn Off,
Method or Scanning Method.
continue entering code numbers
Repeat the steps above for all compo- listed for that brand until the
Component turns Off.
nents. (DTA, TV).
STEP4 After you've entered the correct
B. Quick Set-up Code Tables
code number and the Component
DTA
has turned Off, press the [POWER]
Quick Number Manufacturer/Brand
button to turn the Component
0 PACE DTA
back On. Now it is time to test the
1 SA/CISCO, SAMSUNG, PACE DIGITAL
VOLUME and MUTE buttons for
2 MOTOROLA DIGITAL
the TV to make sure they all work.
3 MOTOROLA DTA
If any of the functions do not work
4 EVOLUTION DTA
as they should, repeat from STEP
5 CISCO IPTV
3 using the next 3-digit code num-
6 ADB IPTV
ber listed for that brand until you
7 TECHNICOLOR
find the best code.
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV
STEP5 Once you have found the correct
3-digit code, save it by pressing fy the code number, so you can
the same [COMPONENT] button
record it for future reference.
one more time. The POWER LED
STEP1 Press the [COMPONENT] but-
light will blink twice to confirm that
ton (TV or DTA) you want to
the code was successfully stored.
verify and the OK button simul-
D. Auto-Search Method
taneously for 3 seconds. The
POWER LED light will turn on
STEP1 Turn on the Component you
want to program (TV, DTA). for 20 seconds.
STEP2 Press the [COMPONENT] button Press the [INFO] button and
STEP2
(TV or DTA) to be programmed
count the number of times the
and OK button simultaneously
Component LED light blinks.
for 3 seconds. The POWER LED
This number indicates the first
light will turn on for 20 seconds
digit of the code, followed by
indicating the unit is ready to be
the second and third, each sep-
programmed.
arated by a one second pause
STEP3 Point the remote toward the
when the LED will turn off.
Component and press the [CH5]
*Note : 10 blinks represents the
or [CH6] button one step at a
number zero.
time or keep it pressed. The
remote will emit a series of
Example : One blink, (pause), eight
ON/OFF commands. Release the
blinks, (pause) and three
[CH5] or [CH6] button as soon
blinks, indicates code
as the Component turns Off.
number 183.
STEP4 Test functions. (Same as for 3-
Digit Code Programming Method F. Programming Volume Control
- Section C). If any of the func-
Volume and Mute control are factory-
tions do not work as they should,
programmed to automatically transfer
repeat from STEP 3 using [CH5]
to the respective Component mode you
or [CH6] buttons to find the cor-
select, as follows:
rect code.
Save the code. (Same as for
STEP5 DTA : DTA T V : TV
3-Digit Code Programming
However, you can program the volume
Method - Section C).
controls (Volume Up, Volume Down
Now, repeat the Auto-Search Method and Mute) from one Component to
for those Components you could operate in another Component.
not program earlier with the Pre-
If you wish to store the TV volume
Programmed Method.
control in DTA mode, use the follow-
ing steps.
E. Finding a Component Button's
Setup Code Number
Press the [DTA] button and
STEP1
the [OK] button simultane-
If you used the Auto-Search Method
ously for 3 seconds.
to program a Component, you may
The [DTA] Component LED
not know what the correct code num-
will turn on for 20 seconds.
ber is. Here is a way for you to identi-