Universal Remote Control UR2-211 Operating Manual

Operating Manual
1
Introduction
For Easy Clicker This remote control is designed
to operate most Digital, Analog
Cable boxes, IPTV set top boxes
UR2-211 and TVs.
2
Replacing Batteries
Before you program or operate the
remote control, you must install
two new AA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3 Replace the battery com-
partment cover.
4
Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either
the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method
A. Quick Set-Up Method
Universal Remote Control, Inc. (Refer to the Section B Quick Set-up table of codes)
www.universalremote.com
STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
OCE-0082E REV 18 (08/26/16)
3
Button Functions
Macro Button
For future use
STEP2 Press and hold the [DEVICE]
TV
Quick Number Manufacturer/Brand
key for 5 seconds until the
0 SANYO
Device LED will blink once
1 SONY
and stays on. Continue to hold
2 SAMSUNG
the [DEVICE] key and press 3 LG
4 TOSHIBA
the number key assigned to
5 PANASONIC
your brand in the Quick Set-
6 PHILIPS
up Code Table and release
7 HITACHI
8 SHARP
both [DEVICE] key and the
9 VIZIO
number key to save the code.
The Device LED will blink
C. C. Manual Programming Manual Programming
twice to confirm that the code
The remote control can be programmed
is stored.
by entering a three-digit code number
STEP3 Point the remote control at the
that corresponds to particular brands
component.
and models of equipment. The three-
STEP4 Press the power button. If it digit code numbers are listed in the
turns off, it is programmed for code tables sections of this instruction
your component. If it does not
manual.
turn off, use the Pre-
STEP1 Turn on the equipment that
Programmed 3-Digit code
you want the remote con-
Method or Scanning Method.
trol to operate (Cable Box or
Repeat the steps above for all
TV).
components (CBL, TV).
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
B. Quick Set-up Code Tables B. Quick Set-up Code Tables
simultaneously for 3 seconds.
CBL The corresponding device
Quick Number Manufacturer/Brand
LED will turn on indicating
0 PACE DTA
that it is ready to be pro-
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL grammed. The LED will remain
3 MOTOROLA DTA
on for 30 seconds. The next
4 EVOLUTION DTA
step must be entered while
5 CISCO IPTV
6 ADB IPTV
the LED is on.
7 TECHNICOLOR
8 AMINO 140/540 IPTV
STEP3 Point the remote control
9 MOTOROLA IPTV
toward the equipment and
enter the three-digit code
number assigned to your
brand from the code tables. STEP1 Turn on the equipment that
If there are more than one
you want the remote control
three-digit number listed for to operate (Cable Box or TV).
your brand, try one code
STEP2 Press the [DEVICE] button
number at a time until your
and the [OK/SEL] button
equipment turns off.
simultaneously for 3 seconds.
*Note: You can verify that you have The device LED will turn on
selected the correct code by indicating that it is ready to
pressing the [POWER] button. be programmed. The LED
will remain on for 30 seconds.
The equipment should turn
back on. Then try all of the The next step must be enter-
functions on the remote ed while the LED is on.
control (i.e. volume, mute,
STEP3 Press the [CH5] or [CH6]
etc.) to ensure you have the
button one at a time or keep
correct code. If any of the
it pressed. The remote will
functions do not operate as
emit a series of Power
they should, repeat the
ON/OFF code signals. Release
instructions from STEP 3
the [CH5] or [CH6] button
above using the next three
as soon as the equipment
digit code number from the
turns off.
brand list.
*Note: You can verify that you have
STEP4 Store the three-digit code
selected the correct code by
by pressing the same
pressing the [POWER]
[DEVICE] button once again.
button. The equipment
The device LED will blink
should turn back on. Then
twice to confirm that the
try all of the functions on
code has been stored.
the remote control (i.e.
D. Auto Search Method
D. Auto Search Method
volume, mute, etc.) to ensure
you have the correct code. If
If none of the three digit code numbers
any of the functions do not
assigned to your brand of equipment
operate as they should,
works, or the code table does not list
repeat the instructions from
your brand, you can use the Auto
STEP 3 above to continue
Search Method to find the correct
the Auto Search Method.
three-digit code number for your
equipment by following steps: STEP4 Press the same [DEVICE]
button to store the code.