Universal Remote Control UR2-DTA Operating Instructions

Operating Instructions For 1
Introduction
UR2-DTA
UR2-DTA
The is designed to
operate the S/A, Pace Micro,
Motorola and IPTV set tops, plus
DTA Remote Control the majority of TV equipment on
the market as shown below.
DTA : DTA boxs, IPTV set tops
TV : Televisions
2
Replacing Batteries
Before you program or operate the
remote control, you must install two new
AA alkaline batteries.
STEP1 Remove the battery compart-
ment cover on the back of your
remote control.
STEP2 Check battery polarity carefully,
and install the batteries as
shown in the illustration below.
STEP3 Replace the battery compart-
ment cover.
3
Operations
Volume Default: DTA volume and mute
through the DTA, with the option of
controlling volume and mute through
the TV. Refer to Section F for program-
Universal Remote Control, Inc.
ming the volume and mute through
www.universalremote.com
your TV.
OCE-0089B REV 11 (07/10/17)
4
Button Functions
5
Programming the Remote Control
There are three ways you can program your remote:
* Quick Set-Up Method
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
The Quick Set-Up Method is a unique new feature that enables the fastest and
easiest set-up by using one-digit codes for up to 10 major brands for each compo-
nent.
The Pre-Programmed Code Method allows you to setup all the buttons at once by
entering 3-digit code numbers that correspond to a particular Component's manu-
facturer/brand, so it's the fastest and easiest of the two methods. (Code Tables
are on the backside of this Instruction Sheet.) The Auto-Search Method scans
through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTE!
TV
Quick Number Manufacturer/Brand
This pertains to all programming steps.
0 SANYO
When you are in setup mode, the DTA
1 SONY
LED will light for 20 seconds.If you do not
2 SAMSUNG
press a button within 20 seconds, the LED
3 LG
light will turn off and exit setup mode and
4 TOSHIBA
you will need to start over.
5 PANASONIC
6 PHILIPS
A. Quick Set-Up Method
7 HITACHI
8 SHARP
STEP1 Turn on the component you
9 VIZIO
want to program. To program
your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key
C. Pre-Programmed 3-Digit Code
for 5 seconds until the DTA LED
Method
will blink once and stays on.
Continue to hold the [DEVICE]
STEP1 Turn on the Component you want
key and press the number key
to program(TV, DTA).
assigned to your brand in the
STEP2 Press the [DEVICE] button (TV or
Quick Set-up Code Table and
DTA) to be programmed and
release both [DEVICE] key and
[SEL] button simultaneously for
the number key to save the
3 seconds. The DTA LED light
code. The DTA LED will blink
will turn on for 20 seconds indi-
twice to confirm that the code is
cating the unit is ready to be
stored.
programmed.
STEP3 Point the remote control at the
STEP3 Point the remote control toward
component.
the Component and enter the 3-
STEP4 Press the power button. If it
digit code number assigned to
turns off, it is programmed for
your brand.
your component. If it does not
*Note : If the 3-digit code number you
turn off, use the Pre-
just entered is correct, the
Programmed 3-Digit code
Component will turn Off. If it
Method or Scanning Method.
did not turn Off, continue
Repeat the steps above for all compo-
entering code numbers listed
nents. (DTA, TV).
for that brand until the
B. Quick Set-up Code Tables
Component turns Off.
DTA
STEP4 Once you have found the cor-
Quick Number Manufacturer/Brand
rect code, save it by pressing
0 PACE DTA the same [DEVICE] button one
1 SA/CISCO, SAMSUNG, PACE DIGITAL more time. The DTA LED light
2 MOTOROLA DIGITAL
will blink twice to confirm that
3 MOTOROLA DTA
the code was sucessfully stored.
4 EVOLUTION DTA
D. Auto-Search Method
5 CISCO IPTV
6 ADB IPTV
STEP1 Turn on the Component you
7 TECHNICOLOR
want to program (TV, DTA).
8 AMINO 140/540 IPTV
STEP2 Press the [DEVICE] button (TV or
9 MOTOROLA IPTV
DTA) to be programmed and
[SEL] button simultaneously for one second pause when the
3 seconds. The DTA LED light LED will turn off.
will turn on for 20 seconds indi-
*Note : 10 blinks represents the
cating the unit is ready to be
number zero.
programmed.
Example : One blink, (pause), eight
STEP3 Point the remote toward the
blinks, (pause) and three
Component and press the [CH5]
blinks, indicates code
or [CH6] button one step at a
number 183.
time or keep it pressed. The
remote will emit a series of F. Programming Volume Control
ON/OFF commands. Release the
By default, the VOL+, VOL- and MUTE
[CH5] or [CH6] button as soon
keys operate through your DTA.
as the Component turns Off.
If you would like those keys to operate
STEP4 Once you have found the cor-
those functions on a TV device,
rect code, save it by pressing
follow these steps.
the same [DEVICE] button one
Press the [SEL] button and
more time. The DTA LED light STEP1
will blink twice to confirm that [DTA] button simultaneously
the code was successfully stored. for 3 seconds.
The DTA LED will turn on for
Now, repeat the Auto-Search Method
20 seconds.
for those Components you could
The next step must be
not program earlier with the Pre-
Programmed Method. perfomed while the LED is on.
STEP2 Press the [VOL+] button.
E. Finding a Component Button's
Setup Code Number
The DTA LED will blink.
If you used the Auto-Search Method
STEP3 Press the [TV] button
to program a Component, you may
that you would like the vollume
not know what the correct code num-
and mute buttons to control.
ber is. Here is a way for you to identi-
The DTA LED will blink twice
fy the code number, so you can
to confirm the programming.
record it for future reference.
Press the [DEVICE] button (TV
STEP1
*Note : If you wish to have the vol-
or DTA) you want to verify and
ume and mute keys operate
the [SEL] button simultaneous-
your DTA Box, press the
ly for 3 seconds. The DTA LED
[DTA] device button in Step 3.
light will turn on for 20 sec-
onds.
STEP2 Press the [INFO] button and
G. Memory Lock System
count the number of times the
DTA LED light blinks. This num- This remote control is designed to
ber indicates the first digit of the retain programmed memory for 10
years even after batteries are
code, followed by the second
removed from the remote control.
and third, each separated by a