Universal Remote Control Easy Clicker UR2-211 Operating Manual

Operating Manual
1
Introduction
For Easy Clicker This remote control is designed
to operate most Digital, Analog
Cable boxes, IPTV set top boxes
UR2-211 and TVs.
2
Replacing Batteries
Before you program or operate the
remote control, you must install
two new AA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3 Replace the battery com-
partment cover.
4
Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either
the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method
A. Quick Set-Up Method
Universal Remote Control, Inc. (Refer to the Section B Quick Set-up table of codes)
www.universalremote.com
STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
OCE-0082E Rev 05 (01/10/13)
3
Button Functions
Macro Button
For future use
STEP2 Point the remote control at the
TV
Quick Number Manufacturer/Brand
component.
0 SANYO
1 SONY
STEP3 Press and hold the [DEVICE]
2 SAMSUNG
key for 5 seconds until the
3 LG
Device LED will blink once
4 TOSHIBA
and stays on. Continue to hold
5 PANASONIC
6 PHILIPS
the [DEVICE] key and press
7 HITACHI
the number key assigned to
8 SHARP
your brand in the Quick Set-
9 VIZIO
up Code Table. The
C. C. Manual Programming Manual Programming
component should turn off as
soon as the number key is
The remote control can be programmed
pressed. (If it does not turn off,
by entering a three-digit code number
release the [DEVICE] key and
that corresponds to particular brands
use the Pre-Programmed 3-
and models of equipment. The three-
Digit code Method or
digit code numbers are listed in the
Scanning Method.)
code tables sections of this instruction
STEP4 Release the [DEVICE] key to
manual.
save the code. The Device
STEP1 Turn on the equipment that
LED will blink twice to confirm
you want the remote con-
that the code is stored.
trol to operate (Cable Box or
Repeat the steps above for all
TV).
components (CBL, TV).
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
B. Quick Set-up Code Tables B. Quick Set-up Code Tables
simultaneously for 3 seconds.
CBL The corresponding device
Quick Number Manufacturer/Brand
LED will turn on indicating
0 PACE
that it is ready to be pro-
1 SCIENTIFIC ATLANTA/CISCO
PACE, SAMSUNG grammed. The LED will remain
2 MOTOROLA
on for 30 seconds. The next
3 AMINO 130/530
step must be entered while
4 EVOLUTION
5 CISCO IPTV
the LED is on.
6 ADB
7 MOXI STEP3 Point the remote control
8 AMINO 140/540
toward the equipment and
9 MOTOROLA IPTV
enter the three-digit code
number assigned to your
brand from the code tables. STEP1 Turn on the equipment that
If there are more than one
you want the remote control
three-digit number listed for to operate (Cable Box or TV).
your brand, try one code
STEP2 Press the [DEVICE] button
number at a time until your
and the [OK/SEL] button
equipment turns off.
simultaneously for 3 seconds.
*Note: You can verify that you have The device LED will turn on
selected the correct code by indicating that it is ready to
pressing the [POWER] button. be programmed. The LED
will remain on for 30 seconds.
The equipment should turn
back on. Then try all of the The next step must be enter-
functions on the remote ed while the LED is on.
control (i.e. volume, mute,
STEP3 Press the [CH5] or [CH6]
etc.) to ensure you have the
button one at a time or keep
correct code. If any of the
it pressed. The remote will
functions do not operate as
emit a series of Power
they should, repeat the
ON/OFF code signals. Release
instructions from STEP 3
the [CH5] or [CH6] button
above using the next three
as soon as the equipment
digit code number from the
turns off.
brand list.
*Note: You can verify that you have
STEP4 Store the three-digit code
selected the correct code by
by pressing the same
pressing the [POWER]
[DEVICE] button once again.
button. The equipment
The device LED will blink
should turn back on. Then
twice to confirm that the
try all of the functions on
code has been stored.
the remote control (i.e.
D. Auto Search Method
D. Auto Search Method
volume, mute, etc.) to ensure
you have the correct code. If
If none of the three digit code numbers
any of the functions do not
assigned to your brand of equipment
operate as they should,
works, or the code table does not list
repeat the instructions from
your brand, you can use the Auto
STEP 3 above to continue
Search Method to find the correct
the Auto Search Method.
three-digit code number for your
equipment by following steps: STEP4 Press the same [DEVICE]