24. Dnie; Remote Control; Installing Batteries In The Remote Control - Samsung HLN4365W1 Instruction Manual

Your New Wide TV

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote,
always point it directly at the TV. The remote control can also operate your Set Top Box, VCR, cable box,
and DVD player.
1. POWER 17. UP, Down, Left, Right
( ▲ , ▼ , œ
Turns the TV on and off.
Press to select highlight up, down, left, or right.
2. S.MODE
While using the on-screen menus, press ENTER
Adjust the TV sound by selecting one of the
to activate (or change) a particular item.
preset factory settings (or select your personal,
18. MTS(Multichannel
customized sound settings.)
Television Stereo)
3. P.MODE
Press to choose stereo, mono or Separate Audio
Adjust the TV picture by selecting one of the
Program (SAP broadcast).
preset factory settings (or select your personal,
customized picture settings.)
19. SURROUND
4. +100
Press to hear the Dolby surround effect.
Press to select cable channels over 100 on TV.
20. ADD/DEL
Press to add or erase channels in the TV's
5. VOL -, VOL +
memory.
Press to increase or decrease the volume.
Use the ADD/DEL button to memorize/erase
the fine tuning after fine tuning channels.
6. MUTE
21. SLEEP
Press to mute the TV sound.
Press to select a preset time interval for
7. FAV.CH (Favorite Channel)
automatic shutoff.
Press to switch between your favorite channels.
22. PIP
8. MENU
Activates picture in picture.
Displays the main on-screen menu.
23. SET
9. STILL
Used during set up of this remote control, so
Press to stop the action during a particular
that it will work compatibly with other devices
scene. Press again to resume normal video.
(VCR, STB, cable box, DVD, etc.)
10. P.SIZE

24. DNIe

Press to change the screen size. Activates DNIe (Digital Natural Image engine).
25. PIP controls
11. MODE
SWAP; Exchanges the video signal that is
Selects a target device to be controlled by the
currently displayed on the main screen with the
Samsung remote control (i.e., TV, VCR, Cable, or
signal in the PIP window.
DVD).
SIZE; Press to make the PIP window larger or
12. PRE-CH
smaller.
Tunes to the previous channel.
CH(PIP); Displays the available channels in
13. TV/VIDEO
sequence. (These buttons change channels in
the PIP window only.)
Press to display all of the available video
sources (i.e., TV, STB, VCR, DVD, DTV, PC). 26. VCR controls
Controls VCR tape functions: Rewind, Play, Fast
14. CH
and CH
Forward, Stop, Pause.
(Channel Up/Down)
27. RESET
Press CH or CH to change channels.
If your remote control is not functioning
properly, take out the batteries and press the
15. INFO
reset button for about 2~3 seconds. Re-insert
Press to display information on the TV screen.
the batteries and try using the remote control
16. EXIT again.
Press to exit the menu.
16
, √ )/ENTER

Installing Batteries in the Remote Control

With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won't be using the remote
control for a long time, remove the batteries and store them in a cool dry place.
Slide the back cover all the way out
1
to open the battery compartment of
the remote control.
2 Install two AAA size batteries.
Make sure to match the "+" and
"–" ends of the batteries with the
diagram inside the compartment.
3 Slide the cover back into place.
17