• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect this equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Page 3
SELF. REFER SERVICING TO QUALIFIED PERSONNEL. Note: • This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere. • This DVD-R2000 is designed and manufactured to respond to the Region Management Infor- mation.
Using the Disc View Function ...28 3D Sound Function ...29 To Watch TV or VCR Playback (or Other Equipment) ...30 If You Want to Record TV Program & Line Input Signal ...31 Changing Setup Menu ...32 Using the Setup Menu ...32 Set the Current Date and Current Time in General Options Mode ...32...
Page 5
To Protect the Recorded Title from being Deleted...52 Using the CD/MP3 Disc View Function ...53 To Program in Specific Sequence ...54 To Playback the Programmed Songs in the Program Window...55 To Delete the Programmed Songs in the Program Window...56 Changing to the Normal mode...56 Using the PROGRAM button ...57...
Batteries for Remote Control (AAA Size) Install Batteries in the Remote Slide the back cover all the way out to open the battery compartment of the remote. Install two AAA size batteries. Make sure to match the “+” and “—” ends of the batteries with the diagram inside the compartment.
• If there are any gaps (blank data) on multi-session discs, you may experience playback prob- lems. • On discs that are recorded with a Variable Bit Rate (VBR), e.g. from 32 to 320 kbps, the sound may cut in and out.
Both the DVD-R2000 and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this player is shown on the rear panel of the player.
Page 9
• Do not open the cartridge shutter with your hands. • Some cartridges are able to eject the disc inside. Even if you can eject the disc, always use the disc with the cartridge. If you want to take out the disc, please refer to the disc instruc- tions.
Œ REC LED ´ STANDBY / ON LED When the DVD-R2000 is first plugged in, the indicator lights. When POWER is pressed on again, the light goes out and the player is turned on. ˇ POWER Turns the DVD-R2000 on and off.
Page 11
Front Panel Display Œ Disc type indicators ´ Repeat play mode( ALL or A-B ) ˇ Dolby Digital Disc ¨ Linear PCM audio output ˆ DTS( Digital Theater System ) output Ø MPEG-2 audio output ∏ MP-3 audio output ” Reverse playback / Pause / Forward play- back / Record ’...
Use the audio cable to connect to the audio output jack on your VCR, cam- corder or other component. ˆ S-VIDEO OUT JACKS If your TV has an S-Video input jack, you can connect an S-Video cable for increased video quality. Ø VIDEO OUT JACKS Use a video cable to connect to the Video input jack on your TV.
Page 13
Use these jacks to connect the audio out- put signals when using the component video output jacks. ’ INTERLACE SCAN OUTPUT JACKS (525I) Use these jacks to connect to a TV with Component video input jacks for a higher quality picture. ( Y, P and P Setup ˝...
Œ DVD POWER Button ´ NUMBER Buttons ˇ 3D Button/+100 Button Use to simulate a 3D Surround effect from 2 stereo speakers. Press to select cable channel over 100 on TV. ¨ REPEAT Button Allows you to repeat play a title, chapter, track, or disc.
Displays the current disc mode. – JOG button & JOG/SHUTTLE Dial Press the JOG button and the red lamp will be lit. Turn the Jog / Shuttle Dial to play back frame by frame. If you turn the Jog / Shuttle Dial without pressing the JOG button, it will play back in fast or slow motion.
Page 16
• CHANNEL (Channel up/down) Button • TV/VIDEO Selection Button TV POWER Button Turns the TV on and off. Use to turn off or set the remote control to control a compatible TV (See page 57). ÷ RECORDER CONTROLS • PLAY LIST Button This button does not work with this model.
If your TV doesn’t have component video, use the S-Video or the basic video connection. If your TV has S-Video Input jack, connect the S-Video cable to the S-Video Output jack on the back of your DVD-R2000 and to the S-Video jack on your TV.
Connect the audio cables to the Audio Output L(left-white) and R (right-red) jacks on the back of your DVD-R2000, and to the corresponding Audio Input (1 or 2 )jacks on your Audio AMP. Method 3 : How to connect the Audio when using component video (Y, P...
2. Connect Audio cables between the Audio OUTPUT jacks on the VCR ( or CAMCORDER) and the Audio INPUT jacks on the DVD-R2000. 3. Press INPUT SELECT button to select the input signal (L1, L2 or L3) connected to the VCR or the camcorder (DVD-R2000 stop mode).
Playing a Disc Before Playback • Turn on a TV and press the TV/VIDEO button to select video mode. • Turn on your audio system and select AUX, CD or DVD-R2000. • After plugging in the player, the first time, press the DVD-R2000 POWER button.
When you stop disc play, the DVD-R2000 remembers where you stopped. When you press PLAY again, it will pick up where you left off (unless the disc is removed, the STOP button is pressed twice or the player is unplugged.) MP3 discs will play from the beginning of the track.
ENTER button. (CD, VCD) To make the screen disappear, press the DISPLAY button again. Note CD: The NUMBER buttons can’t be used while the programmed track is being played. Using Elapsed Time (Except MP3) During playback, press the DISPLAY button on the remote.
• When in search mode (2X/4X/8X/16X/32X) on a DVD/DVD-RAM or high-speed playback on a VCD, no sound will be heard. • When 2X SCAN AUDIO is set to ON in the SETUP MENU, no sound will be heard on discs which are recorded with LPCM, DTS or MPEG-2. (See page 38)
To make the screen disappear, press the AUDIO button again. Using the SUBTITLE button When a DVD is recorded with subtitles, you can select a desired subtitle quickly and easily with the SUBTITLE button on the remote. Press the SUBTITLE button on the remote.
Selecting the Desired Screen Angle & Using the Zoom Using the ANGLE button (DVD only) When a DVD contains multiple angles of a particular scene, you can select the Angle function. Check to see if an ‘ANGLE ( corner of the screen.
• DVD repeats playback by title or, chapter. CD, VCD and MP3 repeat playback by all or track. • Depending on the disc, the Repeat function may not work. • If the title or track is completed before marking the end (B), the end of title or track becomes B automatically.
Basic Functions Using the Bookmark Function The Bookmark function lets you select parts of a DVD, VCD (MENU(PBC) OFF mode) or CD so that you can quickly find the section at a later time. Using the Bookmark Function (Except DVD-RAM, MP3) While the programmed track is being played, the bookmark function doesn’t operate.
Track View (VCD)/Index View (VCD) This function works in VCD1.1 & 2.0 mode (MENU (PBC) OFF mode). In stop mode on VCD, press the ANGLE button and the TRACK VIEW will be displayed directly. During playback, press the ANGLE button on the remote control.
DVD-R2000 to your stereo system, you can enhance sound quality and produce a greater surround effect. This feature is useful when you are using the DVD-R2000 with a two channel stereo through the analog outputs. (Discs which are recorded with LPCM or DTS will not work.
Channel Mode to delete unnecessary channels. (see page 33) Viewing VCR Playback First check that the external input 1 or 2 on the back of DVD-R2000 is connected to a VCR. (L3 at the front of DVD-R2000) Then, turn on the power of the DVD-R2000, TV and VCR.
If You Want to Record a TV Program or Line Input Signal You can use a DVD-RAM disc to record any program or a component connected to a line input. First have a recordable RAM disc prepared. Release the write protect of the RAM disc.
Changing Setup Menu Using the Setup Menu The Setup menu lets you set up the time, TV channel settings, recording type selection, various audio functions, display settings, language settings and parental control. In stop mode, press the SET UP button on the remote.
Page 33
Changing Setup Menu Setting the Current Date and Current Time in General Options Mode This setting is required to perform timer recording. In stop mode, press the SET UP button on the remote. - Setup menu will be displayed. Use the UP/DOWN button to select the “General Options”.
Changing Setup Menu To select Tuner Mode in General Options Mode Set the tuner mode to TV or CATV, depending on the signal coming in to your home. Use the UP/DOWN button to select the Tuner Mode in General Options. Press the ENTER button.
Page 35
Changing Setup Menu Adding and Deleting Channels (Add-Delete Channel) To add or delete a particular channel from memory: Use the UP/DOWN button to select Channel Setting in General Options. Press the ENTER button. Use the UP/DOWN button to select Add-Delete Channel.
Use the UP/DOWN button to select Format Disc in General Options. Press the ENTER button. Use the LEFT/RIGHT button to select Yes. Press the ENTER button. Notes • During formatting, do NOT power off or open your disc tray. • Formatting the disc will erase all previous contents.
Use the UP/DOWN button to select the desired item. Press the ENTER button. 1) Just Recording: If you want to select the recording mode automatically by the time remaining on RAM disc. The Just Recording function is available during only Timer Recording.
Turns 2X audio on. - Off : Turns 2X audio off. Though 2X SCAN AUDIO is ON in the Setup Menu, no sound will be heard on discs which are recorded with LPCM, DTS or MPEG-2. 5) Audio Reception: Stereo or SAP Use the UP/DOWN button to select the desired item.
Black bars will appear at the top and bottom of the screen. - 4:3 pan & screen : Select this for conventional size TV when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.) - 16:9 wide : You can view the full 16:9 picture on your widescreen TV.
Language Selection If you set the audio language, subtitle and disc menu language in advance, they will come up automatically every time you watch a movie. In stop mode, press the SET UP button on the remote. Use the UP/DOWN button to select Language Selection.
Setting Up the Parental Control The Parental Control function works in conjunction with DVDs that have been assigned a rating. This helps you control the types of DVDs that your family watches. There are up to 8 rating lev- els on a disc.
Press the RECORD button to change the recording time during OTR. - If you press the Record button while OTR has been running, the remaining time of OTR will be displayed. Press the Record button once again and 0:30 ¡ 1:00,...
Before timer recording • The current date and time must be set on the Setup menu. (See page 33) • The timer recording scheduling can be done only when the DVD-R2000 has a RAM disc or a disc is not inserted.
Page 44
Press the CLEAR button. To make the timer REC scheduling menu disappear, press the TIMER button again or press the RETURN/INPUT button. Advanced Functions 05 / 31 12 : 41 Am 02 : 42 Pm N o r m a l F P...
Page 45
• When you press the POWER button during the timer recording, the timer recording will stop. • When the remaining disc memory is smaller than the amount of the time set, the recording will only be done within the remaining disc memory.
To Use Edit Function This function lets you edit the recorded title name and info, and set protection mode. Press EDIT button on the remote. - Title List window is displayed. 1) Title Info : Displays information of the currently selected title.
- Title List window is displayed. Select a desired title using the LEFT/RIGHT/UP/DOWN button to delete, and then press the ENTER button. Select “Yes” using the UP/DOWN button to edit, and then press the ENTER button. - Title Edit window is displayed.
Page 48
Use the UP/DOWN button to select “Entire title” in Delete menu, and then press the ENTER button. Select “Yes” using the UP/DOWN button to delete, and then press the ENTER button. - “Delete completed” message is displayed. - Select No to cancel.
Use the UP/DOWN button to select Delete in the Edit Menu, and then press the ENTER button. - Title Delete window is displayed. Use the UP/DOWN button to select Part of title, and then press the ENTER button. - Delete Part of Title window is displayed.
Page 50
- The range which is set with start and end icons is deleted. To make the edit menu disappear, press the EDIT button again. NOTE • The time from the start point to the end point must be more than two seconds. Otherwise, it doesn’t be deleted. Advanced Functions...
ENTER button. - Edit up to 64 characters. - To delete entered characters one by one, use the back space on the screen key board or the CLEAR button on the remote control. Move the cursor to ENTER of the screen key board using the UP/DOWN/LEFT/RIGHT button, and then press the ENTER button.
- Title List window is displayed. Select a desired title using the LEFT/RIGHT/UP/DOWN button that you want protect dialing, and then press the ENTER button. Title Select window is displayed. Use the UP/DOWN button to select “Yes”, and then press the ENTER button.
• Every window displays a maximum of 10 tracks or files. • The maximum the Directory can hold is 200. • The maximum the Track List can hold is 400. • You can display up to 12 characters for each file (except the mp3 extension) and each directory. <MP3>...
To Program in Specific Sequence You can program your favorite songs or tracks in the Directory in a preferred sequence. Press the TOP MENU button on the remote. - The “Navigator-Program” window is displayed. Use the LEFT/RIGHT button to select the DIRECTORY window.
Use the UP/DOWN button to select the desired track. Press the ENTER button. - The selected music is played . - The tracks or files are played back in programmed sequence (program order). To make the “Navigator-Program” window disappear, press the TOP MENU button or RETURN/INPUT button.
To make the “Navigator-Program” window disappear, press the TOP MENU button or RETURN/INPUT button. NOTE • Programmed tracks can not be deleted during program playback, you must be in normal mode. • The programs are all deleted when pressing the OPEN/CLOSE button is pressed or the power is turned off.
Using the PROGRAM button Program playback lets you setup a specific order to playback tracks. You can program the tracks in the sequence you prefer. (See page 55.) Normal Order : Play tracks as they appear on the disc During playback, press the PROGRAM button.
Reference Controlling TV with the Remote Control The remote control can also be set up to control most TVs. To program the remote control, use the code that corresponds to your brand. Turn on the TV Point the DVD’s remote control at the...
Options Menu. Forgot password. • Press power on from a cold start with no disc in the unit. Press the STOP and PLAY buttons simultaneously on the front panel for three seconds. Press the SETUP button on the remote control to select Parental control, and then press the ENTER button.
Power Consumption Recording Format Recording Disc Recording Mode Recording Time Image Signal Mode Playback Media Net Size (W x H x Dmm) (W x H x Dinches) Net Weight (kg) (lb) S-Video In/Output Video In/Output Component Video Out Analog Audio In/Output...
SAMSUNG’s authorized service center. To receive warranty service, the original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAM- SUNG’s authorized service center. Transportation to and from the service center is the responsibility of the purchaser.
Page 62
THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLU- SIVE REMEDY. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This war- ranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Page 63
This warranty will automatically be voided for any unit found with a missing or altered serial number. This warranty is valid only on prod- ucts purchased and used in Canada.
Page 65
SAMSUNG ELECTRONICS AMERICA INC. 105 CHALLENGER ROAD, RIDGEFIELD PARK, NJ 07660 U.S.A. FOR YOUR NEAREST SAMSUNG SERVICE CENTER DIAL 1-800-SAMSUNG AH68-00636Z...