Advertisement
Installation Instructions for Cosco
The Double Snap-N-Go
Infant Car Seat. Please follow these instructions for proper installation of
the Cosco
.
®
Front Seat:
1. Remove (unscrew) Crossbars A1, C and D from the Double Snap-N-Go
frame. Leave Crossbar B1 in hole labeled #4. Remove the Car Seat Straps
from the Double Snap-N-Go
2. Attach Crossbar B1 (removed from the rear section of the Double Snap-
frame), so that the bent section faces down, to the Double Snap-N-
N-Go
®
frame using the two holes labeled #5. Use the two screws that you
Go
®
removed in step 1. Please see figure 1.
3. Attach both Car Seat Straps to the Double Snap-N-Go
two holes labeled #3. Use the two screws that you removed in step 1.
Please see figure 1.
Rear Seat
1. Remove (unscrew) Crossbars A2 and B1 from the Double Snap-N-Go
frame. Remove the Car Seat Straps from the Double Snap-N-Go
Retain the screws you remove.
2. Attach Crossbar C (removed from the front section of the Double Snap-N-
frame) to the Double Snap-N-Go
Go
®
#4. Use the two screws that you removed in step 1. Please see figure 2.
3. Attach both Car Seat Straps to the Double Snap-N-Go
two holes labeled #1. Use the two screws that you removed in step 1.
Please see figure 2.
Insertion of the Cosco
1. With one hand grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car seat
and gently place the seat, so that the baby faces the rear, onto the Double
so that the rear small grooves on the seat bottom hook over
Snap-N-Go
®
Crossbar B1 for the front position or Crossbar C for the rear position.
Release the handle and check that the seat locked onto the bar. See
FOR SAFE OPERATION, IT IS VERY IMPORTANT
Figure 3.
THAT THE REAR LATCHES OF THE SEAT LOCK SECURELY
ONTO THE CROSSBAR.
2. Feed the Car Seat Straps through the slots found on the rear of the Car
Seat shell as shown in figure 4. Buckle the two straps together. The first
time your do this, you will need to adjust the length of the strap for a tight
fit around the car seat. Please see figure 4.
3. Test for secure installation by moving the car seat in all directions. The
car seat should be securely attached to the Double Snap-N-Go
Removal of the Cosco
1. Unlock the Car Seat Strap and remove.
2. With one hand, grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car and
lift the car seat upward from the Double Snap-N-Go
Cosco
and Designer/Opus 35
®
not associated with Baby Trend and no approval or endorsement is implied.
will accommodate the Cosco
®
frame. Retain the screws you remove.
®
frame using the two holes labeled
®
Designer/Opus 35 Infant Car Seat
®
Designer/Opus 35 Infant Car Seat
®
are the trademarks of their owners. They are
Designer/Opus 35
®
Designer/Opus 35
®
frame using the
®
®
frame using the
®
.
®
. See Figure 5.
®
Hole #5
Bar B1
down
®
Hole #4
Bar C
®
frame.
Hole #3
Hole #4
Strap
Bar B1
Fig. 1
Hole #1
Hole #3
Bar B2
Strap
Fig. 2
Fig. 3
Fig. 4
Fig. 5
9
Advertisement
