Zte MF910L Quick Start Manual

Getting to Know Your Device
Appearance
The following figure is for your reference only.
MF910L
Quick Start Guide
1. Power Key
2. WPS Key
• Press and hold for 3 seconds to activate the
WPS function.
• Press to view the Wi-Fi SSID and password on
the LCD screen.
ZTE CORPORATION
3. (U)SIM Card Cover and Reset Hole
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
4. LCD Screen
Postcode: 518057
5. Charging/micro-USB Jack
Getting to Know Your Device Getting to Know Your Device
Indicators Connection Scenarios
When the device is powered on, the following icons may The device can access the Internet in two ways and it
be displayed on the LCD screen. For a description of the allows multiple clients to surf on the Internet at the same
icons, refer to the following table. time. The following figures are for your reference only.
• 4G Mode: A (U)SIM card can be used to access the
Icon Description
Internet.
Network signal strength.
Network system type. The 4G, 3G
or 2G icon is displayed on the LCD
2G, 3G, 4G
screen depending on the connected
network.
The user is in roaming status.
• Internet Wi-Fi Mode: Your device can be connected
to a WLAN device (such as a hotspot device or
Connected to the Internet.
wireless router) through Wi-Fi to access the Internet.
One or more new messages are The WLAN device must be already connected to the
received. Internet.
NOTE: Your device and the WLAN device must be in
Wi-Fi status and the number of
different subnets.
connected users.
Battery level.
Getting to Know Your Device Installing Your Device
Installing Your Device
3. Close the (U)SIM card cover.
1. Open the (U)SIM card cover.
NOTE:
Connecting to Your Device
Do not remove the cover rudely, because it is connected
with the device.
Using Wi-Fi
1. Power on your device.
2. Make sure your computer or other client devices
have enabled Wi-Fi, and search for available
wireless networks.
NOTE: Refer to your Wi-Fi-enabled client device
manual for further details on how to search for
2. Install a (U)SIM card to the (U)SIM card slot.
wireless networks. If you use a computer, you
WARNING! Your device does not support the micro-
need to set your computer to obtain an IP address
SIM card and nano-SIM card or any other non-standard
automatically.
SIM cards. To avoid damage to the device, do not use
those cards or any card holders.
Connecting to Your Device
Getting to Know the Wi-Fi SSID and
Password
3. Select the Wi-Fi name (SSID) of your device, and
click Connect.
You can use the following methods to get the default Wi-
4. Enter the Wi-Fi password if necessary, and click OK.
Fi SSID and password.
NOTE: Refer to the chapter Getting to Know the
• View the label on the device.
Wi-Fi SSID and Password to get the default Wi-Fi
• Press the WPS Key. The Wi-Fi SSID is displayed on
SSID and password. the screen.
5. Wait until the client device is connected to your NOTE: Your device don't have Wi-Fi connection
device successfully. password, it will keep turning on.
Logging in to the 4G Mobile Hotspot
Using a USB Cable
Configuration Page
1. Connect a computer to your device with a USB
cable.
1. Make sure the connection between your device and
2. Power on your device. The operating system detects
the client device is correct.
and identifies new hardware, and automatically
2. L a u n c h t h e I n t e r n e t b r o w s e r a n d e n t e r
installs the hardware.
http://192.168.1.1 or
NOTE: If the system does not automatically launch
http://www.smartbrosettings.net in the address bar.
installation, you can run the installation program in NOTE: It is recommended that you use IE (7.0 or
later), Firefox (15.0 or later), Opera (10.0 or later),
the My Computer / Smartbro PocketWifi path.
Safari (4.0 or later), or Google Chrome (10.0 or
3. Wait until the computer is connected to your device
later).
successfully.
3. Enter the password to log in to the 4G Mobile
Hotspot configuration page.
NOTE: The default password is smartbro.
Changing the Wi-Fi SSID or Pass-
word
1. Log in to the 4G Mobile Hotspot configuration page.
2. Select Settings > Wi-Fi Settings > Basic Settings.
3. Change the Network Name (SSID) or the Pass
Phrase ( Password) in the
Main SSID/Guest SSID
area .
4. Click Apply.
Accessing the Internet
4G Mode
After a client device is successfully connected to your
device, you can access the Internet in Automatic or
Manual mode. The default mode is Automatic.
Mode Operation
Your device is automatically connected
Automatic to the Internet, and you can surf on the
Internet through the client.