Omron HEM-6121 Instruction Manual

HEM-6121-AP_A_M_EN.fm 1 ページ ２０１３年５月１４日 火曜日 午後６時７分
Display:
Wrist Blood
Pressure Monitor
Model HEM-6121
Instruction Manual
F. Systolic blood pressure
1887244-1A
G. Diastolic blood pressure
Introduction H. Heartbeat symbol
1. Flashes during measurement
Thank you for purchasing the OMRON HEM-6121 Wrist Blood
2. If flashing after measurement
Pressure Monitor.
completed or when viewing
results stored in the memory,
The OMRON HEM-6121 is a compact and easy to use blood
indicates blood pressure out of
pressure monitor, operating on the oscillometric principle. It
recommended range*.
measures your blood pressure and pulse rate simply and quickly.
I. Pulse display and Memory
For comfortable controlled inflation without the need of pressure
number
pre-setting or re-inflation the device uses its advanced "IntelliSense"
technology.
Intended Use
2. Preparation
This product is designed to measure the blood pressure and pulse
rate of people within the range of the designated wrist cuff, following
2.1 Installing/Replacing the Batteries
the instructions in this instruction manual.
It is mainly designed for general household use. Please read the
1. Remove the battery cover.
Important Safety Information in this instruction manual before using
the unit.
Please read this instruction manual thoroughly before using the
unit.
Please keep for future reference.
For specific information about your own blood pressure,
CONSULT YOUR DOCTOR.
Important Safety Information 2. Insert two 1.5V "AAA"
alkaline (LR03) batteries
Consult your doctor prior to using in pregnancy or if diagnosed with
as indicated in the battery
arrhythmia or arteriosclerosis.
compartment and then
Please read this section carefully before using the unit.
Warning:
replace the battery cover.
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Notes:
(General Usage)
• If the battery low symbol (
• Always consult your doctor. Self-diagnosis of measurement results
the unit then replace both batteries at the same time.
and self-treatment are dangerous.
• The measurement values continue to be stored in memory
• People with severe blood flow problems, or blood disorders, should even after the batteries are replaced.
consult a doctor before using the unit, as cuff inflation can cause
internal bleeding. Disposal of used batteries should be carried out in accordance
with the national regulations for the disposal of batteries.
(Battery Usage)
• If battery fluid should get in your eyes, immediately rinse with
plenty of clean water. Consult a doctor immediately.
3. Using the Unit
Caution:
Indicates a potentially hazardous situation which, if not avoided, may 3.1 Applying the Wrist Cuff
result in minor or moderate injury to the user or patient or damage to
Do not apply over clothing.
the equipment or other property.
(General Usage) 1.
Place the wrist cuff over
• Do not leave the unit unattended with infants or persons who
your wrist.
cannot express their consent.
• Do not use the unit for any purpose other than measuring blood
Your palm should face upward.
pressure.
• Do not use a mobile phone or other devices that emit
electromagnetic fields, near the unit. This may result in incorrect
operation of the unit.
• Do not disassemble the unit or wrist cuff.
• Do not operate the unit in a moving vehicle (car, airplane).
(Battery Usage)
2. Wrap the wrist cuff around
• If battery fluid should get on your skin or clothing, immediately rinse
your wrist.
with plenty of clean water.
• Use only two "AAA" alkaline (LR03) batteries with this unit.
Wrap the wrist cuff securely
• Do not insert the batteries with their polarities incorrectly aligned.
around the wrist for taking
• Replace old batteries with new ones immediately. Replace both
accurate measurements.
batteries at the same time.
• Remove the batteries if the unit will not be used for three months or
more.
• Do not use new and used batteries together.
General Precautions
• Do not apply strong shocks and vibrations to or drop the unit.
• Do not take measurements after bathing, drinking alcohol or
Make sure that the wrist cuff
caffeine, smoking, exercising or eating.
does not cover the protruding
• Do not inflate the wrist cuff when it is not wrapped around your
part of the wrist bone (ulna) on
wrist.
the outside of the wrist.
• Read and follow the "Important information regarding Electro
Magnetic Compatibility (EMC)" in the Technical Data Section.
• Read and follow the "Correct Disposal of This Product" in the
Technical Data Section when disposing of the device and any used
accessories or optional parts. Note: You can take a
measurement on either
your left or right wrist.
1. Overview
Main unit:
A 3.2 How to Sit Correctly
D
B
To take a measurement, you need
to be relaxed and comfortably
seated, under comfortable room
temperature. No bathing, drinking
alcohol or caffeine, smoking,
E
C
exercising or eating 30 minutes
before taking a measurement.
A. Wrist cuff
D. Memory ( ) button
B. Battery compartment E. START/STOP button
• Sit on a chair with your feet flat on the
C. Display
floor.
• Sit upright with your back straight.
• The cuff should be at the same level
as your heart.
• Relax your wrist and hand. Do not bend your wrist back, clench
your fist, or bend your wrist forward.
3.3 Taking a Reading
Notes:
• To cancel a measurement, press the START/STOP button at
J
F
any time during measurement.
K
• Remain still while taking a measurement.
L
1. Press the START/STOP button.
G
All the symbols appear on the display.
M
The wrist cuff will start to inflate automatically.
H
Cuff Wrapping Guide
N
I
J. Memory symbol
K. Irregular heartbeat symbol
L. Cuff wrapping guide
M. Deflation symbol
START INFLATE
N. Battery low symbol
Cuff Wrapping Guide
* Note: If your systolic or diastolic
pressure is outside the standard
The Cuff wrapping Guide is a unique feature that indicates if
range (above 135/85 mmHg) the
the cuff is not wrapped tightly enough around the wrist.
Heartbeat symbol ( ) will blink.
If the is displayed, it means the reading is NOT reliable
Please refer to Section 3.3.
due to the incorrect wrapping of the cuff.
Please wrap the cuff again, taking care to wrap it correctly and
take the measurement again. When the
the cuff is correctly wrapped tightly enough on the wrist and
the reading is accurate and reliable.
2.
Undo the wrist cuff and remove the unit.
3. Press the START/STOP button to turn off the
monitor.
The monitor automatically stores the measurement in its
memory.
It will automatically turn off after two minutes.
Important:
• If your systolic or diastolic pressure is
outside the standard range, the
heartbeat symbol will blink when the
measurement result is displayed.
Recent research suggests that the
following values can be used as a
) appears on the display, turn off
guide to high blood pressure for
measurements taken at home.
Systolic Blood Pressure
Diastolic Blood Pressure
This criteria is for home blood pressure measurement.
• Your blood pressure monitor includes an
irregular heartbeat feature. Irregular
heartbeats can influence the results of the
measurement. The irregular heartbeat
algorithm automatically determines if the
measurement is usable or needs to be
repeated. If the measurement results are
affected by irregular heartbeats but the result
is valid, the result is shown together with the
irregular heartbeat symbol (
If the irregular heartbeats cause the measurement to be
invalid, no result is shown. If the irregular heartbeat symbol
( ) is shown after you have taken a measurement, repeat
the measurement. If the irregular heartbeat symbol (
shown frequently, please make your doctor aware of it.
Notes:
• Wait 2 - 3 minutes before taking another blood
pressure measurement. Waiting between readings
allows the arteries to return to the condition prior to
taking the blood pressure measurement.
• The blood pressure can differ between the right arm
and the left arm, and therefore also the measured
blood pressure values can be different. OMRON
recommends to always use the same arm for
measurement. If the values between the two arms
differ substantially, please check with your doctor
which arm to use for your measurement.
Warning:
Self-diagnosis of measured results and treatment are
dangerous. Please follow the instructions of your doctor.
3.4 Using the Memory Function
The unit automatically stores up to 30 sets of measurement
values (blood pressure and pulse rate). If the memory is full,
the monitor will delete the oldest readings.
To View the Readings Stored in Memory
1. Press the button.
The Memory number
appears for a second
before the pulse rate is
displayed. The newest
set is numbered "1".
DEFLATE COMPLETE
Note: If there are no
measurements results
stored in the memory, the
screen to the right is
displayed.
is displayed,
2.
Press the button repeatedly to view the
readings stored in memory.
To Delete All the Values Stored in Memory
When the memory symbol ( ) appears, first press
the button. Then while holding it down, press the
START/STOP button simultaneously for about 2 - 3
seconds.
First Second
Note: You cannot partially delete the stored readings.
Above 135 mmHg
4. Troubleshooting and Maintenance
Above 85 mmHg
4.1 The Icons and Error Messages
Error Display Cause Remedy
Remove the wrist cuff. Wait
2 - 3 minutes and then take
another measurement.
Irregular heartbeats
Repeat the steps in section
are detected.
3.1, 3.2 and 3.3. If this error
continues to appear, contact
your doctor.
).
You should replace them with
The batteries are
new ones ahead of time.
Blink
low.
Refer to section 2.1.
) is
You should replace them with
The batteries are
new ones at once.
Lit
exhausted.
Refer to section 2.1.
Wrist cuff not Apply the wrist cuff correctly.
applied correctly. Refer to section 3.1.
Repeat Measurement while
remaining still and refrain
Movement during
from talking during the
measurement.
measurement.
Refer to section 3.3.
Apply the wrist cuff correctly
and repeat measurement
Wrist cuff not
while remaining still and
applied correctly, or
refrain from talking during the
movement during
measurement.
measurement.
Refer to section 3.1, 3.2 and
3.3.
Contact your local OMRON
Device error.
representative.
Note: The irregular heartbeat symbol ( ) may also be displayed
with error messages.
13A0093
4.2 Troubleshooting
5. Technical Data
Problem Cause Remedy Product Description
Model
Measure while in the
Display
The wrist cuff is not
correct posture.
Measurement Method
at heart level.
Refer to section 3.2.
Measurement Range
The cuff is not
Wrap the cuff correctly.
Accuracy
wrapped snugly
Refer to section 3.1.
The reading is around the wrist.
Inflation
extremely low
The arms and Relax and try taking the
(or high). Deflation
shoulders are measurement again.
Memory
tense. Refer to section 3.3.
Power Source
Battery Life
Movement or Remain still and do not
talking during talk during Measurement.
measurement. Refer to section 3.3.
Applied Part
Wrist cuff pressure Air is leaking from Consult your local
does not rise. the wrist cuff. OMRON representative.
Protection Against
Electric Shock
Apply the cuff correctly so
Operating temperature/
Wrist cuff deflates The wrist cuff is that it is firmly wrapped
Humidity
too soon. loose. around the wrist. Refer to
Storage temperature/
section 3.1.
Humidity
Blood pressure readings Console Weight
constantly vary with time Outer Dimensions
The blood pressure is different of day and how relaxed
each time. The reading is you are. Take several Measurable Wrist
extremely low (or high). deep breaths and try to Circumference
remain relaxed before
Cuff Material
taking a measurement.
Package Content
The unit loses
Replace the batteries with
power during
Note: Subject to technical modification without prior notice.
The batteries are
new ones.
measurement.
exhausted.
Refer to section 2.1.
Nothing happens
• This device fulfils the provisions of EC directive 93/42/EEC
when you press The batteries have Insert the batteries with
(Medical Device Directive).
been inserted the correct (+/-) polarity.
the buttons.
• This blood pressure monitor is designed according to the European
incorrectly. Refer to section 2.1.
Standard EN1060, Non-invasive sphygmomanometers Part 1:
General Requirements and Part 3: Supplementary requirements
• Press the START/STOP button and repeat
for electromechanical blood pressure measuring systems.
measurement.
• If the problem continues, try replacing the
Other problems.
batteries with new ones.
If this still does not solve the problem, contact
Important information regarding Electro Magnetic
your local OMRON representative.
Compatibility (EMC)
With the increased number of electronic devices such as PC's and
mobile (cellular) telephones, medical devices in use may be
4.3 Maintenance
susceptible to electromagnetic interference from other devices.
Electromagnetic interference may result in incorrect operation of
To protect your unit from damage, please observe the
the medical device and create a potentially unsafe situation.
following:
Medical devices should also not interfere with other devices.
In order to regulate the requirements for EMC (Electro Magnetic
• Do not subject the main unit and the cuff to
Compatibility) with the aim to prevent unsafe product situations, the
extreme temperatures, humidity, moisture or
EN60601-1-2:2007 standard has been implemented. This standard
direct sunlight.
defines the levels of immunity to electromagnetic interferences as
well as maximum levels of electromagnetic emissions for medical
• Do not disassemble the unit.
devices.
• Do not subject the unit to strong shocks or
This medical device manufactured by OMRON HEALTHCARE
vibrations (for example, dropping the unit on the
conforms to this EN60601-1-2:2007 standard for both immunity and
floor).
emissions.
Nevertheless, special precautions need to be observed:
• Do not use volatile liquids to clean the main unit.
• Do not use mobile (cellular) telephones and other devices, which
• Do not wash the cuff or immerse it in water.
generate strong electrical or electromagnetic fields, near the
• Do not use petrol, thinners or similar solvents to
medical device. This may result in incorrect operation of the unit
and create a potentially unsafe situation. Recommendation is to
clean the cuff.
keep a minimum distance of 7 m. Verify correct operation of the
• Do not carry out repairs of any kind yourself. If a
device in case the distance is shorter.
defect occurs, consult your OMRON retail outlet
Further documentation in accordance with EN60601-1-2:2007 is
or distributor as mentioned on the packaging.
available at OMRON HEALTHCARE EUROPE at the address
mentioned in this instruction manual.
Documentation is also available at www.omron-healthcare.com.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its
literature, indicates that it should not be
disposed of, with other household wastes at the
end of its working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this product from
other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
• The unit should be cleaned with a soft, dry cloth.
of where and how they can return this item for environmentally safe
• Use a soft, moistened cloth and soap to clean
recycling.
the cuff. Business users should contact their supplier and check the terms
and conditions of the purchase contract. This product should not be
• Keep the unit in its storage case when not in
mixed with other commercial wastes for disposal.
use.
• Fold the cuff into the storage case.
Do not store the unit in the following situations:
• If the unit is wet.
• Locations exposed to extreme temperatures,
humidity, direct sunlight, dust or corrosive
vapours. Asia Pacific HQ
• Locations exposed to vibrations, shocks or
where it will be at an angle.
Production Facility
Calibration and Service
This OMRON product is manufactured under the strict quality
• The accuracy of this blood pressure monitor has
system of OMRONHEALTHCARE Co., Ltd., Japan. The Core
been carefully tested and is designed for a long
component for OMRON blood pressure monitors, which is the
service life.
Pressure Sensor, is produced in Japan for assembly.
• It is generally recommended to have the unit
inspected every two years to ensure correct
functioning and accuracy. Please consult your
authorised OMRON dealer or the local
representative.
Wrist Blood Pressure Monitor
HEM-6121
LCD Digital Display
Oscillometric method
Pressure: 0 to 299 mmHg
Pulse: 40 to 180 beats/min.
Pressure: ±3 mmHg
Pulse: ±5% of display reading
Automatic inflation by pump
Automatic rapid deflation
30 Measurements
2 x 1.5V (LR03, AAA alkaline batteries)
Approx. 300 measurements with new
alkaline batteries at a room temperature of
23°C
= Type B
Internally powered ME equipment
+10 to +40°C / Maximum: 30 to 85% RH
-20 to +60°C / Maximum: 10 to 95% RH /
700 to 1060hPa
Approx. 101g without batteries
Approx. 78 (w) mm x 60 (h) mm x 21 (d)
mm (without the wrist cuff)
Approx. 13.5 to 21.5 cm
Nylon and polyester
Main unit, storage case, battery set,
instruction manual
OMRON HEALTHCARE Co., Ltd.
53, Kunotsubo, Terado-cho, Muko, Kyoto,
617-0002 JAPAN
OMRON HEALTHCARE EUROPE B.V.
Scorpius 33, 2132 LR Hoofddorp
THE NETHERLANDS
OMRON HEALTHCARE SINGAPORE PTE LTD.
438A Alexandra Road, #05-05/08
Alexandra Technopark, Singapore 119967
www.omron-healthcare.com.sg
OMRON HEALTHCARE MANUFACTURING
VIETNAM CO., LTD.
Binh Duong Province, Vietnam
Made in Vietnam