Planet WGS-803 User Manual

1. Package Contents
Thank you for purchasing PLANET 8-Port 10/100/1000T
Wall-mounted Gigabit Ethernet Switch, WGS-803.
Open the box of the WGS-803 Gigabit Ethernet Switch
and carefully unpack it. The box should contain the
following items:
z The WGS-803 Gigabit Ethernet Switch x 1
z User Manual x 1
z DIN-rail Kit x 1
z Wall-mounted Kit x 1
z Magnet Kit x 1
z 3-pin Terminal Block Connector x 1
z RJ45 Dust-proof Cap x 8
If any item is found missing or damaged, please contact
your local reseller for replacement.
- 1 -
2. Hardware Description
The front panel of the WGS-803 Gigabit Ethernet Switch
consists of 8 Auto-sensing 10/100/1000Mbps Ethernet
RJ45 Ports. The LED Indicators are also located on the
RJ45 ports of the Gigabit Ethernet Switch.
10/100/1000BASE-T RJ45 Port
3-pin Terminal Block
DC Plug-in 10/100/1000BASE-T RJ45 Port
- 2 -
2.1 Terminal Block Connector Pinouts
To install the 3-pin Terminal Block Connector on the
WGS-803, simply follow the following steps:
Step 1: Insert positive DC power wire into V+,
negative DC power wire into V-, and grounding
wire into Ground.
Ground
V
-
V+
Step 2: Tighten the wire-clamp screws for preventing
the wires from loosening and plug into the
wall-mounted switch.
1. The wire gauge should be in the range
from 12 to 24 AWG
2. The device must be grounded
Note
3. The DC power input range is 12V ~ 48V DC
2.2 LED Indicators
 System
LED Color Function
Lights to indicate that the Switch has
PWR Green
power.
- 3 -
 10/100/1000BASE-T Interfaces
LED Color Function
Lights To indicate the link through
that port is successfully
established.
LNK/
Green
ACT
Blinks To indicate that the switch is
actively sending or receiving
data over that port.
Lights To indicate that the port is
operating at 1000Mbps.
Off If LNK/ACT LED is lit, it
indicates that the port is
1000 Green
operating at 10/100Mbps.
If LNK/ACT LED is Off, it
indicates that the port is link-
down.
- 4 -
2.3 Product Specifications
Model WGS-803
Hardware Specifications
Network
8-port RJ45 for 10/100/1000BASE-T
Connector
MAC Address 8K MAC address table with auto
Table learning function
Data Buffer 64Kbytes
Switch Fabric 16Gbps
Switch
11.9Mpps@64bytes
Throughput
Back pressure for half duplex. IEEE
Flow Control
802.3x pause frame for full duplex
Power
12~48V DC, 0.5A (max.)
Requirements
Power
6 watts/20BTU
Consumption
ESD Protection 6KV DC
EFT Protection 6KV DC
Enclosure IP30 aluminum
- 5 -
Dimensions
148 x 24.2 x 134 mm
(W x D x H)
Weight 498g
Standard Conformance
IEEE 802.3 Ethernet
Standard IEEE 802.3u Fast Ethernet
Compliance IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Flow Control
Regulatory
FCC Part 15 Class A, CE
Compliance
Environment
Temperature: -10 ~ 60 degrees C
Operating Relative Humidity: 5 ~ 95%
(non-condensing)
Temperature: -20 ~ 70 degrees C
Storage Relative Humidity: 5 ~ 95%
(non-condensing)
- 6 -
2.4 Physical Dimensions (WxDxH):
148 x 24.2 x 134mm
118.00
148.00 24.20
133.00
134.00 118.00 6.00
Ground
V
-
V+
Dimensions ( unit = mm )
- 7 -
3. Installation
3.1 Wall Mount Installation
To install the WGS-803 Gigabit Ethernet Switch on the
wall, simply follow the following steps:
Step 1: There are 4 holes with 8mm diameter on
the wall; the distance between the 2 holes is
133mm and the line through them must be
horizontal.
Step 2: Install a conductor pipe inside the board hole
and flush the edge of the conductor pipe with
the wall surface.
Step 3: Screw the bolts into the conductor pipe. The
WGS-803 is between bolts and conductor pipe,
as shown below.
- 8 -