Advertisement
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2017 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
17i
®
Advertisement
Table of Contents
Related Manuals for CEN-TECH 63873
Summary of Contents for CEN-TECH 63873
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: Table Of Contents
Wear ANSI-approved splash-resistant safety goggles. Volts Read the manual before Alternating Current set-up and/or use. Amperes WARNING marking concerning Risk of Fire. Cold Cranking Amps Follow connection procedure. Reserve Capacity Page 2 For technical questions, please call 1-888-866-5797. Item 63873... -
Page 3: Safety Instructions
Incorrect reassembly may These batteries may burst and cause injury result in a risk of electric shock or fire. to persons and damage to property. i. NEVER charge a frozen battery. Item 63873 For technical questions, please call 1-888-866-5797. Page 3... - Page 4 Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger 20. This product is not a toy. diameter than NEGATIVE (NEG, N,–) post. Keep it out of reach of children. Page 4 For technical questions, please call 1-888-866-5797. Item 63873...
- Page 5 – Risk of Fire or Electric Shock. accordance with all local codes and ordinances. Connect battery charger directly to grounding receptacle (three-prong). An adapter should not be used with battery charger. Item 63873 For technical questions, please call 1-888-866-5797. Page 5...
-
Page 6: Specifications
Wheel. Bend ends of Cotter Pin up. Push Cotter Pin through hole on Axle next to Wheel. Bend ends of Cotter Pin up. 5. Snap Hubcaps (22) onto Axle. Axle Hubcap cotter Wheel Page 6 For technical questions, please call 1-888-866-5797. Item 63873... - Page 7 Screws (27). a. Remove two top screws on each side of Charger. b. Align Handle with mounting holes. c. Attach Handle with screws. Handle Screws Screws Screw cable Storage pegs Screw Item 63873 For technical questions, please call 1-888-866-5797. Page 7...
-
Page 8: Operation
XX S: Cooling countdown. c. MAINTENANcE: Comes on when battery is fully charged. h. EF-03: Reconditioning failed. d. VOLTAGE: Comes on when i. EF-04: Charge aborted. voltage is being displayed. Page 8 For technical questions, please call 1-888-866-5797. Item 63873... -
Page 9: Preparing To Charge
3/4 - 2 hr 550-875 CCA 85-125 RC 35 - 55 hr 7 - 11 hr 2 - 3 hr WARNING! TO pREVENT SERIOUS INJURy, FIRE, AND pROpERTy DAMAGE: Monitor charging during use. Item 63873 For technical questions, please call 1-888-866-5797. Page 9... -
Page 10: Charging Battery Installed In Vehicle
Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. connect to a heavy gauge metal part of the frame or engine block. Page 10 For technical questions, please call 1-888-866-5797. Item 63873... - Page 11 11. After use clean, then store the Charger/ cable as far away from battery as possible – Starter indoors out of children’s reach. then connect NEGATIVE (BLACK) charger clip to free end of battery cable. Item 63873 For technical questions, please call 1-888-866-5797. Page 11...
-
Page 12: Engine Starting
Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. connect to a heavy gauge metal part of the frame or engine block. Page 12 For technical questions, please call 1-888-866-5797. Item 63873... -
Page 13: Maintenance
2. Defective battery, 2. Check and/or replace battery. will not hold full charge. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 63873 For technical questions, please call 1-888-866-5797. Page 13... -
Page 14: Parts List And Diagram
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Internal parts are not user-serviceable and are not available. Page 14 For technical questions, please call 1-888-866-5797. Item 63873... - Page 15 Assembly Diagram Item 63873 For technical questions, please call 1-888-866-5797. Page 15...
-
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.