Advertisement
Quick Links
XE-A22H Quick Start Guide
The following describes how to get the cash register ready to operate. Follow these steps before you use the cash register for the first time.
Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place the cash register.
1
Initializing the Cash
Register
To ensure the cash register operates properly,
please use the following procedure:
1. Make sure the power cord is unplugged and batteries
are not installed on the register.
2. Insert the manager (MA) key into the mode switch and
turn it to the REG position.
REG
OPX/Z
MGR
OFF
VOID
PGM
3. Insert the plug of the power cord into the AC outlet.
The buzzer will sound three times.
IMPORTANT:
This operation must be performed
without batteries installed.
4. The cash register has now been initialized.
The register display will show "0.00" with "
".
2
Installing the Batteries
1. Push the printer cover forward and
detach it.
2. Open the battery
compartment cover next
to the paper roll cradle.
3. Install three new alkaline
batteries LR6 ("AA" size) as
shown at the right. (Batteries
are not supplied with the cash
register.) Make sure that
positive (+) and negative (–)
poles of each battery are
properly oriented.
4. When the batteries are properly installed, "
" on
the display will disappear. Close the battery
compartment cover.
3
Installing the Paper
If you want to use a paper roll for journal printing, please refer
to GETTING STARTED section of the instruction manual.
1. Lift up the print roller
release lever to unlock
and open the print roller
arm.
X1/Z1
X2/Z2
Print roller release lever
2. Set a paper roll in the paper roll cradle as illustrated below.
NOTE: When setting a new
paper roll in the paper roll
cradle, be sure to cut the
paper end behind the taped
Correct
(or pasted) point in advance.
3. Feed the end of the paper along
with the paper positioning guides as
illustrated at the right.
Paper positioning
guides
4. While holding down the paper,
slowly close the print roller arm,
and push down the arm until you
hear a click locking the arm.
Make sure you securely push
down the center of the wing part
of the arm as illustrated at the
right. The paper will be fed
automatically.
5. Cut off the excess paper using
the edge of the inner cover, and
replace the printer cover. Press
the
F
key to make sure the
paper end comes out of the
printer cover and clean paper
appears.
NOTE: If the print roller arm is not securely locked, the unit will not
print correctly. If this problem occurs, open the arm, and close the
arm as instructed above.
4
Basic Programming
(for receipt printing)
Set the mode switch to the PGM position.
Print roller arm
Setting the Date
Enter the date in 8 digits using the month-day-year format.
s
Then press
Example:
08262009 s
Date (August 26, 2009)
Setting the Time
Enter the time in 4 digits ("hhmm" format) using the 24 hour
To the printer
To the printer
system. Then press
Incorrect
Example:
1430 s
Time (2:30 p.m.)
Setting Tax Rates (%)
NOTE: If you are in an area that uses a tax table for tax
calculation, please refer to the programming section in
the instruction manual.
Specify a tax rate (%) for calculation of tax on each taxable
subtotal using the following sequence:
s
9
➔
@
➔
➔ Q ➔
where
R: Tax rate (0.0000% to 100.0000%)
Q: Minimum taxable amount (0.01 to 999.99)
(Smallest amount for which tax must be collected.)
*Up to 4 types of tax are programmable.
Example:
s 9@
1@ 6P25@ 12 s A
Tax 1
Tax rate (6.25%)
Other Programming
While the cash register is pre-programmed so it can be used
with minimal set-up, it does provide you optional features.
For details, please refer to the instruction manual.
Initial settings:
Department 1 to 10:
Department 11 to 99: Non-taxable.
REG
OPX/Z
MGR
OFF
X1/Z1
X2/Z2
VOID
PGM
.
s
.
@
@
➔
➔ Tax number (1 to 4)* ➔
➔ R
s
A
➔
Min. taxable
amount ($0.12)
Taxable 1
Printed in China / Impreso en China
English
5
Now, you are ready!
Before Starting Entries
• Set the mode switch to the REG position.
REG
OPX/Z
MGR
OFF
X1/Z1
X2/Z2
VOID
PGM
Registration Example
(when selling department items by cash)
1. Enter your clerk code. (By default, clerk code 1 is
assigned.)
2. Enter the price for the first department item.
For example for 5.00, enter
5:
, and press the
appropriate department key.
For department 17 to department 32, press
D
first before pressing the department key.
For department 33 and above, enter the
department code using numeric keys, and press
d
, then enter the price and press
d
again.
3. Repeat step 2 for all the department items.
4. Press
s
to display the amount due.
5. Enter the amount received from the customer.
(You can omit this step if the amount tendered is
the same as the subtotal.)
6. Press
A
, and the change due is displayed
(when the amount received was not entered, total
amount is displayed) and the drawer is opened.
7. Tear off the receipt and give it to the customer
with his or her change.
8. Close the drawer.
Key operation example
1L 5:!
Clerk code
Price and dept.1
825D"
Price and dept. 18
s 2:0 A
Amount tendered
When an error occurs:
When an error occurs with an alarm sound, press
l
to clear the error. If you do not clear the error, press
G
twice. The transaction will be finalized in
subtotal void or cash sale.
(TCADH2549RCZZ) 1
Advertisement
