Planet GSD-604HP User Manual

1. Package Contents
Check the following contents of your package:
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
GSD-604HP User's Manual 55V Power Adapter
Power Cord Rubber Feet Wall-mount Kit
x 4
- 1 -
2. Product Features
 RJ45 Interface
 6 10/100/1000Mbps Gigabit Ethernet ports
 4 ports support 54V DC power to PoE powered
device
 Power over Ethernet
 Complies with IEEE 802.3af/at Power over Ethernet
end-span PSE
 Up to 4 IEEE 802.3af/802.3at devices powered
 Supports PoE power up to 30 watts for each PoE
port
 55-watt PoE Budget
 Auto detects powered device (PD)
 Circuit protection prevents power interference
between ports
 Remote power feeding up to 100m
 Hardware
 LED indicators for PoE ready/activity and LINK/ACT
 One 55V DC power jack
- 2 -
 Switching
 Hardware based 10/100/1000Mbps auto-negotiation
and auto MDI/MDI-X
 Flow control for full duplex operation and back
pressure for half duplex operation
 9216 bytes jumbo packet size support
 Integrates address look-up engine, supporting 8K
absolute MAC addresses
 Automatic address learning and address aging
 Supports port-based VLAN and loop protection
3. Switch Front Panel
Figure 3-1 shows the front panel of GSD-604HP.
Uplink
PoE
PWR
1000 LNK
ACT
PoE MAX
10/100 LNK
1 2 3 4
ACT
PoE In-Use
1 2 3 4 5 6
GSD-604HP
Figure 3-1: GSD-604HP Front Panel
- 3 -
4. LED Indicators
System
LED Color Function
Lights: Indicates the Switch has
PWR Green
power.
Per 10/100/1000Mbps Port
LED Color Function
Lights: Indicates the link through
that port is successfully
1000 established at 1000Mbps.
Green
Blinks: Indicates that the Switch is
LNK
actively sending or receiving
data over that port.
Lights: Indicates the link through
that port is successfully
10/100 established at 10/100Mbps.
Orange
LNK Blinks: Indicates that the Switch is
actively sending or receiving
data over that port.
PoE-in-Use Port
LED Color Function
Lights: Indicates the port is providing
PoE Orange
54V DC in-line power.
Lights: 80% of PoE usage
MAX Orange
Blinks: 100% of PoE usage
- 4 -
5. Switch Rear Panel
Figure 5-1 shows the rear panel of GSD-604HP.
55V DC
Please power off before switching DIP.
Port-based VLAN & Loop protection
Enable Disable
Figure 5-1: GSD-604HP Rear Panel
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
Power
Notice
2. In some areas, installing a surge sup-
pression device may also help to protect
your GSD-604HP from being damaged
by unregulated surge or current to the
GSD-604HP or the power adapter
- 5 -
6. Port-based VLAN and Loop
Protection Feature
The GSD-604HP has one feature called Port-based
VLAN and Loop Protection. When switching the DIP to
the "Enable" position, port 1 to port 5 wouldn't able to
communicate with each other.
PoE Uplink
PWR
1000 LNK
ACT
PoE MAX
10/100 LNK
1 2 3 4
ACT
PoE In-Use
1 2 3 4 5 6
GSD-604HP
Port 1 to Port 5 only can communicate with Uplink Port 6.
PoE Uplink
PWR
1000 LNK
ACT
PoE MAX
10/100 LNK
1 2 3 4
ACT
PoE In-Use
1 2 3 4 5 6
GSD-604HP
When there is a loop happening from the client, the
GSD-604HP will block that port and wouldn't allow data
to transfer to the switch.
PoE Uplink
PWR
1000 LNK
ACT
PoE MAX
10/100 LNK
1 2 3 4
ACT
PoE In-Use
1 2 3 4 5 6
GSD-604HP
Loop (broadcast)
- 6 -
7. Installing the Switch
This part describes how to install your Gigabit PoE+
Switch and make connections to it. Please read the
following topics and follow the procedures as presented.
This Gigabit PoE+ Switch does not need
software configuration.
Note
Desktop Installation
To install the Gigabit PoE+ Switch on desktop, simply
follow the following steps:
Step 1: Attach the rubber feet to the recessed areas
on the bottom of the Gigabit PoE+ Switch.
Step 2: Place the Gigabit PoE+ Switch on desktop near
AC power source for its power adapter.
Step 3: Keep enough ventilation space between the
Gigabit PoE+ Switch and the surrounding
objects.
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 8 -- Product Specifica-
Note
tions.
Step 4: Connect your Gigabit PoE+ Switch to network
devices.
- 7 -
A. Connect one end of a standard network cable to
port-5 and port-6 10/100/1000Mbps RJ45 ports on
the front of the Gigabit PoE+ Switch.
B. Connect the other end of the cable to the network
devices such as NVR(Network Video Recorder),
workstations or routers.
Step 5: Connect your Gigabit PoE+ Switch to PoE PD
devices.
A. Connect one end of a standard network cable to port
1 to port 4 10/100/1000Mbps RJ45 ports on the
Front of the Gigabit PoE+ Switch.
B. Connect the other end of the cable to the 802.3at/
af powered devices.
Port 1~Port 4 PoE IP Cameras
PoE PoE PoE PoE
GSD-604HP
Power
Power Line
1000BASE-T UTP
1000BASE-T UTP with PoE
PoE
4 Channel NVR
Port 5~Port 6 Dual Uplink Ports
- 8 -