Byron SX-203 Manual

Model No. SX-203
Wire Free Portable Door Chime Kit with
Record your own sound SX-203
Door Chime Unit
Operating
Distance
Operation
Indicator
100m
Push
Button
Push
Button Unit
No wiring is required for this Wire Free Door Chime Kit. When the Push Button is pressed, it sends a wire free signal to the door chime
unit that activates the chime. As the operating range is up to 100 metres (320 ft. approx. - in open field), you can mount or take the door
chime virtually anywhere in the home. However, the transmission range of the wire free signal will be reduced if the signal is transmitted
through a number of walls or ceilings. Metal, and UPVC doorframes will also reduce the operating range.
Push Button Unit
2 x 3 volt Lithium batteries (CR2032) have already been installed. Your Push Button is ready to use.
To channge
the battery
Remove the back of the case by pushing in Remove the locking screw from the battery
the tab on the bottom with a small, flat fastener. Insert 2 x 3 volt CR2032 Lithium
screwdriver. batteries (Byron SX100) in the battery
compartment, ensuring the battery polarity
matches the internal markings, then tighten
the screw on the battery fastener to hold the
batteries firming in their compartment.
Batteries Batteries
Wire Free
Included Included
CR2032
100m
82db
Operating Loudness
Distance
To mount
This
way
up
Using the two holes on the back of Push
Button as a template, mark the fixing
position for the unit. Drill holes and fit wall
plugs and secure the Push Button unit with
screws (self-tapping N3 x 16mm screw).
Door Chime Unit
Battery
Compartment
To change the batteries
Slides open the battery compartment door. Insert 2 x 1.2 volt alkaline batteries ("AA", UM3 & LR6 - included) into the battery
compartment, ensuring the battery polarity matches the internal markings. It will beep twice to indicate that it is ready for the new
operation code registration (Please see Digital Code Set Up). Close the battery door, then the chime unit is ready to use.
It has a slotted hang hole on the rear of the unit, this will enable the chime unit to be hooked onto a screw and easily removed or
relocated to another room. Drill a hole and fit a wall plug (if fixing to masonry) and screw (self-tapping 3 x 16mm screw) to fixing
position. Leave a gap of 3mm between the screw head and the wall. Locate the keyhole slot on the back of the unit over the screw.
Sound Selection
There are 2 ways to select the desired melodies as your doorbell sound either by switching the sound selection switch to "Music" or
Melody".
a) Music: Doorbell will play the recorded music as the doorbell sound.
b) Melody: Doorbell will play the preset melody as the doorbell sound, there are total of 8 melodies stored.
Melody Selection
The Melody Selector is located inside the Push Button unit, a small switch in the top left corner of battery compartment marked with "S".
Press the switch once, the melody will change to play the next one on the list, there are a total 8 melodies for selection. The Push Button
is pre-set to "Electro Mechanical - Ding Dong" therefore, if no change is required, it should not be adjusted.
Push Button
Melody Selector
1) Electro Mechanical - Ding Dong 3) Jive
2) Westminster - 8 notes 4) Wedding March
Additional Byron "SX" range products can be purchased for compatibility. SX-4 & SX-41 models will not work with other SX
models
Record Your Favourite Music as Door Chime Melody
You can record 10 seconds of your favourite music as your doorbell sound.
1) Firstly switch the sound selection switch (located at the back of doorbell) to the position marked "Music".
2) There are 2 ways to record your own music:
To mount
3mm
Melody
5) Piano 7) Dog Barking
6) Harmony 8) Ringer