Related Manuals for Schlage KING COBRA
Summary of Contents for Schlage KING COBRA
- Page 1 KING COBRA/KING COBRA-2 NARROW STILE SERIES KC9111/KC9111-2 KC9321/KC9321-2 Keypad Programmable and SNAP Compatible Trim For Narrow Stile Doors 57040-E 04-2007...
-
Page 2: Contents Of The Box
KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Contents of the Box KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Contents of the Box 57040-E Page 2 04-2007... -
Page 3: Introduction / Tools And Materials Needed / Contact Info
4. 1/16” Allen wrench 5. Long nose needle-nose pliers 6. Center punch 7. Hammer 8. Pencil 9. Drill & Tap for 10-32 threads Contact Information: Schlage Lock Company 575 Birch Street Forestville, CT 06010 technical support: 866-322-1237 fax: 866-322-1233 web: http://www.irsupport.net 57040-E... -
Page 4: Door Preparation
Installation may require the use of a cover plate (a) to cover the holes left in the door. If the KC9321/KC9321-2 (trim w/turnpiece) is used and the existing pull (b) must be removed, Ives offers a compatible pull. >Schlage Cover Plate P/N: KC9000-KRP >Ives Pull P/N: 8190-18-xxx (xxx = finish) Backset is determined by the Adams Rite®... -
Page 5: Cams, Cores, Cylinders And Blocking Rings
Cams For Mechanical Override Cylinder: Cams, Cores, Cylinders and Blocking Rings The KC9000 trim requires the use of a clover leaf cam (a). This is a list of compatible Schlage parts. For other manufacturers, consult cross-reference charts. > Cam for Standard Mortise cylinder:... - Page 6 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 Installing the KC9111/KC9111-2 or KC9321/KC9321-2 Installing the KC9111/KC9111-2 or KC9321/KC9321-2 If your trim has a key cylinder already installed, skip to Determine Hand: on page 12. Other- wise, continue with Loosen the Baseplate Screws: on this page. 1) Loosen the Baseplate Screws: IMPORTANT: Do not remove any of the screws in the fol- lowing step or it will be difficult to reinstall them.
- Page 7 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 3) Make Room for Key Cylinder: Due to the diameter of the key cylinder, it is necessary to have dead latch (a) placed out of the way when installing the key cylinder. Therefore... Using your finger or a pair of needle-nose •...
- Page 8 • Screw in key cylinder until it stops. Use mechanical key as a han- • dle for turning if necessary. Table 1: Blocking Rings Key Cylinder Length Blocking Ring (Schlage P/N; XXX = finish) • 1-1/4” 1/8” (36-079-012-XXX) • 1-3/8”...
- Page 9 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 8) Alignment of Interchangeable Cores: If an IC Core is used, center the interface toward the • bottom. 9) Tighten the Four Screws in the Baseplate: Tighten the four baseplate screws in the fol- •...
- Page 10 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 11) Position the Dead Latch’s Set Screw Hole: Tilt the trim until you see the “critical • edge” align with the larger hole in the baseplate as shown in photo on right. Look closely at edge of dead latch’s “critical edge”...
- Page 11 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 12) Partially Tighten the Set Screw: Using a 1/16” Allen wrench, partially turn • in the set screw until outer end of set screw is about flush with surface of base- plate.
- Page 12 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 14) Determine Hand: To determine hand: Stand on outside of door. • Determine which arm the hinges are • closest to. If door is pulled to open, it is • “Reverse.” NOTE: All narrow stile trim is “Reverse.”...
- Page 13 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 16) Verifying the Interface Hand: Photo on right shows how your interface should look for a • RHR installation. Note direction of hook (a) in respect to latch (b). NOTE: Hook can be reversed. Verify the Interface Hand (continued): Photo on right shows how the assembled interface should •...
- Page 14 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 18) Remove Interface’s Hook Assembly: Lift off hook assembly (a) from interface. • 19) Flip Hook Over: Remove pin (a) from hook (b). • Flip hook over. • Insert pin back into hook. •...
- Page 15 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 21) Install New Retaining Ring-LHR: Photo on right shows an interface that will be used in • a LHR installation. Observe direction of “finger” (a) on hook assembly. Push new retaining ring (included in screw pack) •...
- Page 16 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 24) Secure the Lever Cover: Secure lever cover with two Phillips head screws. • 25) What To Do With the Adams Rite Product: ® Retrofit Installation - Remove face plate (a). •...
- Page 17 > If necessary, lift off template and reposition. Drill and tap holes. • NOTE: If optional blind nuts are used, see blind nut installation instructions (Schlage Lock Company form number: 57057) for cor- rect hole size and mounting method. 57040-E Page 17...
- Page 18 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 27) Orientation of the Interface: From the outside of the door, posts (a) on interface • should be pointing at you and hook (b) on interface should be facing down. Photo on right shows an interface that is prepared for •...
- Page 19 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 Photo on right shows a RHR installation. Viewed from the inside of the door, this is what the • interface should look like within the door when assembling a RHR installation. >...
- Page 20 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 32) Prepare the Exterior Gasket: Peel paper backing off of exterior gasket (a). • 33) Apply the Exterior Gasket: Apply gasket to back of trim. • If you are installing a prep cover plate, continue with, Install the Interface Spacer: on page 21. Otherwise, skip to, Place Trim On Door: on page 21 57040-E Page 20...
- Page 21 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 34) Install the Interface Spacer: IMPORTANT: This step to be performed ONLY if installing a prep cover plate (a). Place interface spacer (b) onto door. • Place prep cover plate onto door. •...
- Page 22 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 36) Tighten Top Mounting Screw: Using a ball-end, 1/8” Allen wrench, partially tighten • the top screw in trim. IMPORTANT: Do not completely tighten the top screw. Leave loose. 37) Remove Battery Cover: If not already done, insert key into cylinder and turn •...
- Page 23 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 39) Install Batteries: Remove and retain battery bag. • IMPORTANT: DO NOT DISCARD BATTERY BAG. IT IS IMPORTANT THAT IT IS REINSTALLED AFTER THE BATTERIES ARE INSTALLED IN BATTERY HOLDER. Observe the polarity markings indicated on battery holder and install •...
- Page 24 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Installing the KC9111/KC9111-2 or KC9321/KC9321-2 42) Install Battery Compartment Cover: Slide battery compartment cover on from the bottom. • IMPORTANT: Use caution not to pinch the battery wires. Tighten battery cover screw. • Rotate key clockwise. •...
-
Page 25: Test Operation
KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Test Operation Test Operation: Test Operation 1. For KC9111/KC9111-2: Lever should be able to be pushed down, but not up. > If you find that this is not correct, see, Verify Lever / Turnpiece Stop Screw Direction: on page 12 2. - Page 26 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION Dimensions Dimensions: Dimensions 57040-E Page 26 04-2007...
- Page 27 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION NOTES NOTES NOTES 57040-E Page 27 04-2007...
- Page 28 KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION NOTES NOTES 57040-E Page 28 04-2007...