Table of Contents
Advertisement
Air Cooled Chimney *
Collar
Figure 34
SLOPE
ASHT+ * / HT6103+ * / DuraTech
Roof Pitch
0 *
2/12
4/12
6/12
8/12
10/12
12/12
* Cross Slope Hole Size
Put the chimney cap into place.
Wash the roof flashing with a solvent or vinegar, then paint it with rust-proof paint.
Table 3
OFFSET CHIMNEY INSTALLATION
After reaching the location requiring the elbow, proceed as follows. The minimum chimney height
when using elbows is:
Fireplace Model
Chimney Model
Vertical installation
Two (2) elbows
Four (4) elbows
Table 4
Figure 31
NOTES:
• Must return to vertical before penetrating ceiling or floor.
• A maximum of 2 offsets are allowed.
22
AC
Chimney
Spacer (built
into flashing)
Flashing
Roof Down Slope Hole Size
/
S-2100+ * / HT6000+ *
®
DuraTech DTC **
6"
12-3/8" (314 mm)
14-1/8" (359 mm)
12-9/16" (319 mm)
14-3/8" (365 mm)
13" (330 mm)
14-7/8" (378 mm)
13-7/8" (352 mm)
15-3/4" (400 mm)
14-7/8" (378 mm)
16-1/8" (410 mm)
18-3/8" (467 mm)
17-1/2" (445 mm)
Minimum Chimney Height Using Elbows
WRT3920WS
ASHT+ * / S2100+ * / HT6103+ * / HT6000+ * / AC * / DuraTech / DuraTech DTC **
12 feet (3.66 m)
15 feet (4.57 m)
17 feet (5.18 m)
Figure 35
AC *
6"
6"
15" (380 mm)
15 3/8" (390 mm)
16 1/8" (410 mm)
16 7/8" (430 mm)
17" (432 mm)
18 1/4" (465 mm)
19 5/8" (500 mm)
20" (508 mm)
21 3/8" (545 mm)
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
After reaching the location requiring the
elbow, proceed as follows:
ASHT+
/ HT6103+
/ S-2100+
*
*
*
DuraTech DTC
Chimneys
**
1. Install the first elbow; turn it in the required
direction. Fasten it to the chimney with
the three (3) 1/2" (12 mm) metal screws
provided with the elbow.
2. Install the necessary chimney lengths to
achieve the required offset. Lock the chimney
lengths together: it is recommended to use
three (3) 1/2" (12 mm) screws. If the offset
length is made of two (2) chimney lengths or
more, use an offset or roof support halfway
up the offset. If penetrating a wall, install
a wall radiation shield (see Figures 38 and
39).
3. Use another elbow to turn the chimney verti-
cally. Secure the elbow, using three (3) 1/2"
(12 mm) screws (provided with the elbow).
4. Use a plumb-bob to line up the center of
the hole. Cut a hole for the chimney in the
ceiling/floor. Frame this hole as described
previously (refer to section Chimney Instal-
lation Instructions).
5. From below, install a firestop (See Figure
32a).
6. A support (ST
or SO
) must be used on the
*
*
first 15' section (5 m).
7. Continue with the regular installation.
AC Chimney
*
1. Install the first elbow. Turn it in the required
direction. To lock it in place, turn 1/8 of a
turn. Fasten the straps attached to the elbow
to the surrounding frame, using nails or
drywall screws (see Figure 37).
2. Install the necessary chimney lengths to
achieve the required offset. Lock the chimney
lengths together. If penetrating a wall, use
a wall radiation shield.
3. Use another elbow to turn the chimney
vertically. Lock it to the chimney. Fasten
the straps attached to the elbow to the
surrounding framing using nails or drywall
screws.
4. Use a plumb-bob to line up the center of the
hole. Cut a hole for the chimney in the ceiling.
Frame this hole as described previously.
5. From below, install a firestop (see Figure
32b).
6. Continue with the regular installation.
NOTE: When using AC chimney
*
starter section must be used before installing
an elbow. When an offset is needed imme-
diately off the top of the fireplace, an elbow
starter section, AC6SB30
, is available.
*
Available from Security Chimneys
*
**
Available from DuraVent
/ HT6000+
/
*
, an AC6SB
*
®
®
Advertisement
Table of Contents
