Kenwood NX-5400 Service Manual page 42

Item Condition
Panel tuning
mode
2. 1) Adj item: [Manual Adjustment]
Receive [RAST] 1) Adj item:
Assist Adjust:[****] [Receive Assist]
2) Adj item: 2) Adj item:
[Frequency: [Frequency: 700MHz
700MHz Band] Band]
[RX/TA Low]→ [RX/TA Low]→
[RX/TA High] [RX/TA High]
[Frequency: [Frequency: 800MHz
800MHz Band] Band]
[RX/TA Low]→ [RX/TA Low]→
[RX/TA High] [RX/TA High]
Adjust:[***]
Press [ ] key Press [Apply All] but-
to store the ad- ton to store the ad-
justment val- justment value.
ue.
3. 1) Adj item: [Manual Adjustment]
Transmit [TAST] 1) Adj item:
Assist Adjust:[****] [Receive Assist]
2) Adj item: 2) Adj item:
[Frequency: [Frequency: 700MHz
700MHz Band] Band]
[RX/TA Low]→ [RX/TA Low]→
[RX/TA [RX/TA High]→
High]→ [TX Low]→
[TX Low]→ [TX High]
[TX High] [Frequency: 800MHz
[Frequency: Band]
800MHz Band] [TX Low]→
[TX Low]→ [TX High]→
[TX High]→ [RX/TA Low]→
[RX/TA Low]→ [RX/TA High]
[RX/TA High]
Adjust:[***] Press [Transmit] but-
PTT: ON ton.
Press [ ] key Press [Apply All] but-
to store the ad- ton to store the ad-
justment val- justment value.
ue.
1-42 (No.RA016<Rev.001>)
Measurement
PC test mode Test-
equip-
ment
Adjustment
Unit Ter- Unit Parts
minal
Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Specifications
Method
[PC test mode] 2.5V±0.1V
[Automatic Adjust- [Automatic Ad-
ment] justment]
1) Press [Tune Assist After the automatic
Voltage] button. adjustment is per-
2) Press [Apply All] but- formed, verify that
ton to store the adjust- the VCO lock volt-
ment value after the age is within the
automatic adjustment voltage range
has finished. which is specified
[Manual Adjustment] by the manual ad-
[V] indicator on the PC justment.
window shows VCO lock [Manual Adjust-
voltage. Change the ad- ment]
justment value to get Press [Apply All]
VCO lock voltage within button to store the
the limit of the specified adjustment value
voltage. after all adjustment
point have been
Note:
adjusted.
Confirm the VCO lock
voltage approximately Note:
3 seconds after the The assist adjust-
adjustment value is ment value must
changed. be between from
340 to 3550.
[PC test mode] 2.5V±0.1V
[Automatic Adjust- [Automatic Ad-
ment] justment]
1) Press [Tune Assist After the automatic
Voltage] button. adjustment is per-
2) Press [Apply All] but- formed, verify that
ton to store the adjust- the VCO lock volt-
ment value after the age is within the
automatic adjustment voltage range
has finished. which is specified
[Manual Adjustment] by the manual ad-
[V] indicator on the PC justment.
window shows VCO lock [Manual Adjust-
voltage. Change the ad- ment]
justment value to get Press [Apply All]
VCO lock voltage within button to store the
the limit of the specified adjustment value
voltage. after all adjustment
point have been
Note:
adjusted.
Confirm the VCO lock
voltage approximately Note:
3 seconds after the The assist adjust-
adjustment value is ment value must
changed. be between from
340 to 3550.
/Remarks