Si281312E Table of Contents 1. Procedure to Remove Air Filter and Suction Grille .........2 2. Procedure to Remove Decoration Panel..........3 3. Procedure to Remove Horizontal Blade..........4 4. Procedure to Remove Swing Motor ............6 5. Procedure to Remove Switch Box ............7 6.
Procedure to Remove Air Filter and Suction Grille Si281312E 1. Procedure to Remove Air Filter and Suction Grille Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step 1.
Si281312E Procedure to Remove Decoration Panel 2. Procedure to Remove Decoration Panel Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step Removing the suction Relay connector grille according to procedure for removing Relay connector...
Procedure to Remove Horizontal Blade Si281312E 3. Procedure to Remove Horizontal Blade Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step Removing the decoration panel according to Screw on the back side Seal part (A) procedure for removing...
Page 7
Si281312E Procedure to Remove Horizontal Blade Step Procedure Points 3. Removing the horizontal blade Remove the horizontal blade assembly. To remove the horizontal blade, put a screwdriver in the connection and apply the “principle of leverage”. Horizontal blade assembly Removal Procedure...
Procedure to Remove Swing Motor Si281312E 4. Procedure to Remove Swing Motor Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step According to the procedure for the removal of decoration panel, Anti-sweat part remove the decoration...
Si281312E Procedure to Remove Switch Box 5. Procedure to Remove Switch Box Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step According to the procedure for the removal of decoration panel, remove the decoration Fixing screws...
Procedure to Remove PCB Si281312E 6. Procedure to Remove PCB Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step According to the procedure for the removal Fixing screws of decoration panel, remove the decoration...
Si281312E Procedure to Remove Bell Mouth and Drain Pan 7. Procedure to Remove Bell Mouth and Drain Pan Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step According to the procedure for the removal...
Procedure to Remove Fan Motor Si281312E 8. Procedure to Remove Fan Motor Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step According to the procedure for the removal of switch box, remove the switch box.
Si281312E Procedure to Remove Drain Pump, Float Switch 9. Procedure to Remove Drain Pump, Float Switch Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Procedure Points Step According to the procedure for the removal of decoration panel, remove the decoration...
Procedure to Remove Humidity Thermistor and Air Temperature Thermistor Si281312E 10.Procedure to Remove Humidity Thermistor and Air Temperature Thermistor Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Step Procedure Points According to the...
Si281312E Procedure to Remove Heat Exchanger Temperature Thermistor 11.Procedure to Remove Heat Exchanger Temperature Thermistor Procedure Warning Be sure to wait for 10 minutes or more after turning off all power supplies before disassembling work. Step Procedure Points According to the procedure for the removal of decoration panel, remove the decoration...
Page 16
Revision History Month / Year Version Revised contents 06 / 2013 Si281312E First edition...
Page 17
Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion. Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or contractor to install those parts and accessories. Use of unauthorised parts and accessories or improper installation of parts and accessories can result in water or refrigerant leakage, electrical shock, fire or explosion.