Table of Contents
Advertisement
Océ ProCut
Facility Requirements
Facility Requirements
Determine where the cutter system will be located in advance of the installation. Mark this with
Determine where the cutter system will be located in advance of the installation. Mark this with
adhesive tape so that you can confirm the dimensions. Ensure that there is a gap of at least 1 meter
adhesive tape so that you can confirm the dimensions. Ensure that there is a gap of at least 1 meter
to the nearest wall all around the machine to allow access by operating and servicing personnel.
to the nearest wall all around the machine to allow access by operating and servicing personnel.
Two meters at the front end of the system will make media handling much easier.
Two meters at the front end of the system will make media handling much easier.
If the delivery includes a router option, the room must be at least 3 m high. See location
If the delivery includes a router option, the room must be at least 3 m high. See location
Dimensions below for specific model requirements.
Dimensions below for specific model requirements.
Check the room temperature and humidity. Be certain that the environment will meet or exceed the
Check the room temperature and humidity. Be certain that the environment will meet or exceed the
requirements all year long.
requirements all year long.
Provide supports with sufficient stability if the difference in height over the entire installation surface
Provide supports with sufficient stability if the difference in height over the entire installation surface
is greater than 2 cm.
is greater than 2 cm.
Floor Loading
Floor Loading
The subsurface for the machine must be sufficiently level and stable. The floor in the operational
The subsurface for the machine must be sufficiently level and stable. The floor in the operational
location must have adequate load-carrying capacity and stiffness. Wood framed/constructed floors
location must have adequate load-carrying capacity and stiffness. Wood framed/constructed floors
are not suitable! Solid and level concrete surface is recommended. The difference in height over
are not suitable! Solid and level concrete surface is recommended. The difference in height over
the entire installation surface must be less than 2 cm.
the entire installation surface must be less than 2 cm.
Floor Loading: minimum 800 kg / 1,764 lbs. per square meter
Floor Loading: minimum 800 kg / 1,764 lbs. per square meter
Electrical Placement
Electrical Placement
If using wall-mounted power outlets, they can be located on either side or rear of the machine.
If using wall-mounted power outlets, they can be located on either side or rear of the machine.
Depending on distance, extension cords may be needed.
Depending on distance, extension cords may be needed.
If using ceiling power drops, they can be place anywhere behind the PC stand but need to be at
If using ceiling power drops, they can be place anywhere behind the PC stand but need to be at
least 20cm away from the side cover to allow for removal of the side covers during service.
least 20cm away from the side cover to allow for removal of the side covers during service.
Location Dimensions
Location Dimensions
Model
1600 M
1600 XL
1600 XXL
1600 XXXL
2500 L
2500 M
3200 L
3200 XL
3200 XXL
3200 XXXL
Note: A clear distance to the nearest wall etc. of approx. one-meter must be provided and
maintained for operator and service access. The values if the above table includes one-
meter clearance on all sides. Two meters at the front end of the system will make media
handling much easier.
Océ ProCut Site Preparation Guide - Revision: E
Width
Length
4679 mm
5619 mm
6089 mm
6559 mm
5149 mm
4679 mm
5149 mm
5619 mm
6089 mm
6559 mm
Table 3: Location Dimensions
Height w/router
4512mm
4512mm
4512mm
4512mm
5412 mm
5412 mm
6112 mm
6112 mm
6112 mm
6112 mm
3000 mm/118"
3200 mm/125"
3200 mm/125"
3200 mm/125"
3200 mm/125"
3000 mm/118"
3200 mm/125"
3200 mm/125"
3200 mm/125"
3200 mm/125"
Site Prep
5
Hide quick links:
Advertisement
Table of Contents
