Audiovox CD1072 Operating Instructions

CD PROGRAMMED PLAYBACK
A program of up to 32 tracks from all the available discs in the disc tray can be played in a preset order.
1. Press the PROGRAM button (in stop mode).First " P01 " will display for about 2 seconds and then Disc
Number (example 4d) will flash on display. "P01" means you are setting the first programmed track.
PROGRAM
P
2. Press the DISC SKIP button to select the de-
sired disc. (example 5d)
DISC SKIP
PRO GR AM
4. Press the PROGRAM button again to store this
track in memory.
PROGRAM
PRO GRA M
PROGRAM
P
To check the program
After setting, press PLAY button, then press STOP
button. In stop mode, press PROGRAM button to
check the number of programs and the track order.
This will not work when the disc is being played.
To stop programmed play for a moment:
• Press the PLAY/PAUSE button and "
displayed and the current track number will
flash. Press this button again to resume playing.
PROGRAM
To add additional tracks during program playback:
• Press STOP button first, the current playing
disc No. will appear on the display. Press PROGRAM
button, the first programmed No. and the track No.
will appear on the display, repeat steps 2 to 4.
PROGRAM
USING THE CD STORAGE
• Open the CD Storage Door and insert the CD with the CD Box into the storage windows, maximum
to insert six CD.
REMOTE CONTROL (OPTIONAL)
2
3
1
4
5
6
USING THE REMOTE CONTROL CORRECTLY
• Point the Remote Control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be
degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 4 meters (13 feet).
TO CHANGE REMOTE CONTROL BATTERY
1. Open the battery door. 2. Insert one CR2025 (3V)
size battery.
BATTERY REPLACEMENT
When battery becomes weak, the operating distance of the Remote Control is greatly reduced
and you will need to replace the battery.
NOTE:
If the Remote Control is not to be used for a long time, remove the battery to avoid damage
caused by battery leakage corrosion.
MAINTENANCE
CLEANING CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc from the center out with a cleaning cloth. After
playing, store the disc in its case.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
IMPORTANT NOTE:
If an abnormal display indication or an operating problem occurs, disconnect the AC power cord. Wait at
least 5 seconds, then reconnect it. Before transporting the unit, take out all discs from the CD tray.
SPECIFICATIONS
Power requirements
Power consumption
PRO GRA M
PROGRAM
3. Press the / SKIP buttons to select the
desired track. (example the first track of Disc 5)
SKIP/SEARCH
PRO GR AM
5. To add additional tracks, repeat steps 2 to 4.
6. To start playback, press the
PROG RA M
To erase the whole program, do one of the
following:
• Press STOP button twice to erase the program.
• Set the FUNCTION switch to other functions.
• Open the disc tray by pressing the OPEN/CLOSE
button.
" will be
NOTE:
• The same track can be selected more than once
in the same program.
• With program on, the /
available only for the selected tracks.
• With program on, repeat play can be performed
but disc skip function can not be done.
1. -SKIP Button
2. REPEAT Button
3. +SKIP Button
4. DISC SKIP Button
5. PLAY/PAUSE Button
6. STOP Button
ATTENTION
Take out the PVC sheet before operating
the Remote Control.
AC ~ 120V 60Hz (USA/CANADA)
AC ~ 220V 50Hz (other countries)
AC ~ 230-240V 50Hz (Europe)
AC ~ 240V 50Hz (Australia)
AC ~ 110-120V/220-240V 50/60Hz (other countries)
10 W
PLAY/PAUSE button.
WARNING
EXPLANATION OF GRAPHICAL SYMBOLS:
WARNING
skip function is
RISK OF ELECTRIC
SHOCK DONOT OPEN
"WARNING: TO REDUCE THE RISK
O F E L E C T R I C S H O C K , D O N O T
REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL."
WARNING:
The following checks will assist in the correction of most problems which you may encounter with your
system. Before going through the check list below, first check the following points.
SYMPTOM
GENERAL
No sound.
No sound from one channel or unbalanced
left and right volume.
Reversed left and right sound.
Lack of bass sound or apparently imprecise
physical location of musical instruments.
Severe hum or noise.
RADIO RECEPTION
The FM STEREO indicator flashes.
Severe hum or noise.
CD PLAYER OPERATION
Play does not start.
Distorted playback or sound loss during
CD playback.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinch particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Unplug this apparatus during lightening storms or when unused for a long period of time.
13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14) This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid
such as vases shall be placed on the apparatus.
Specifications and external appearance are subject to change without advance notice
due to continuous product improvement.
5 CD CHANGER
HOME STEREO SYSTEM

OPERATING INSTRUCTIONS

The lightning flash with an arrowhead
symbol, within the equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute an electric
shock to persons.
The exclamation point within the
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying
appliance.
TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This product contains a low power laser device.
TROUBLE SHOOTING GUIDE
CAUSE (AND REMEDY)
• Turn VOLUME clockwise.
• The headphones are connected. Disconnect them.
• Check the speaker connections of the inoperative channel.
• Check the speaker cord connection and speaker location.
• Check the speaker connection for proper phasing.
• The TV or VCR is too close to the stereo system. Separate the
stereo system from the TV or VCR.
• Wire the antenna.
• Wire the antenna.
• The disc is not placed correctly.
• Dirty disc.
• The disc is inserted upside down.
• The player is in the pause mode.
• Moisture condensation.
• CD is dirty or scratched.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK
DEFEATED.
AVOID EXPOSURE TO BEAM
CLASS 1 LASER PRODUCT
the
CLASS 1 LASER
PRODUCT
Printed in China
811-107291-051