Download Print this page
Audiovox CE520 Operating Instructions Manual
Audiovox CE520 Operating Instructions Manual

Audiovox CE520 Operating Instructions Manual

Vertical cd home system

Advertisement

Available languages

Available languages

Quick Links

SYSTEM CONNECTIONS
MW/AM
LOOP
ANTENNA
The AC cord to an AC outlet
1.
SPEAKER CORD CONNECTION
Connect the right speaker to the R terminal, and
the left to the L terminal.
Connect the wires with the printed white lines to the
red (+) terminals and the plain-black wires to the black
(-) terminals.
WARNING:
Connecting speakers other than the speakers
supplied with the unit may damage the unit.
2.
CONNECTION WITH OTHER OPTIONAL EQUIPMENT
To listen to or record audio signals from external
units through this unit.
Connect the red plug to the R jack, and the white
plug to the L jack to the AUX jack.
LISTENING TO THE CONNECTED EQUIPMENT
1. Press the FUNCTION button to AUX.
2. Play the external source.
3.
MW/AM LOOP ANTENNA CONNECTION
Caution:
Do not connect to an outside antenna.
• Be sure the AC power cord is disconnected
Connect the supplied MW/AM loop antenna to
and all functions are off before making con-
receive better MW/AM broadcast signal.
nections.
4.
• To prevent electrical shock, match wide
FM ANTENNA WIRE
blade of plug to wide slot, fully insert. (FOR
Do not connect to an outside antenna.
N. America)
5.
POWER CORD CONNECTION
Before use, check that the rated voltage of your
unit matches your local voltage.
Connect the AC cord to an AC outlet.
The STANDBY indicator will light up and the clock
will be displayed.
CD SECTION
CD PLAYING
1. Press the CD button.
CD
2. Press the OPEN/CLOSE button to open CD door. Place
a disc in the CD tray with the label face front and then
OPEN/CLOSE
press the OPEN/CLOSE button to close CD door. The
total number of tracks will show on the display.
NOTES:
• Do not push the CD door to close it.
• CD door cannot open while power is off.
3. To start playing, press
PLAY/PAUSE
TO INTERRUPT PLAYBACK
button.
Press
PLAY/PAUSE button.
The
indicator will light up.
To resume playback, press
PLAY/PAUSE
button again.
TO STOP PLAYBACK
Press
STOP button.
Locating a particular point in a track
Searching for the beginning of a track
To move backward at high speed
To find a previous track
Press
SKIP button once to return to
Keep
SKIP button pressed during play
the beginning of the current track.
and release at the desired point.
Press
SKIP button repeatedly to skip
tracks backward one by one.
To move forward at high speed
Keep
SKIP button pressed during play
To skip tracks
and release at the desired point.
Press
SKIP button repeatedly to skip
track(s) forward one by one.
SKIP/ TUNING
UP
SKIP/ TUNING
UP
DOWN
DOWN
BACKWARD
FORWARD
BACKWARD
FORWARD
Keep it pressed
Press it once
NOTE :
The CD player may skip if the loud speakers are situated close to the player and if high volume or bass
levels are used.
PARTS IDENTIFICATION
1. MODE selector (BEAT CUT/FM
MODE/DUBBING)
2. PHONES jack
3. Cassette Deck A operation buttons
1
PAUSE button
2
STOP/EJECT button
F.FWD button
3
REW button
4
PLAY button
4. Cassette Deck B operation buttons
PAUSE button
STOP/EJECT button
F.FWD button
REW button
5
PLAY button
REC button
5. Cassette knob cover
6
26
6. Cassette Deck A door
7. CD door
8. POWER/STANDBY button
7
9.
CD PLAY/PAUSE button
8
25
10.
/
SKIP/TUNING buttons (UP/
9
24
DOWN)
10
23
11.
CD STOP button
11
22
12
21
12. PRESET/REPEAT button
13
20
13.
MEMORY button
14
19
15
14. RANDOM button
16
15. REMOTE SENSOR
17
16. STANDBY indictor
18
17. X-BASS indicator
18. DISPLAY window
19. TUNER button
20. CD button
21. TAPE button
22. BAND button
23. X-BASS button
24. VOLUME (
/
)
25.
OPEN/CLOSE button
26. Cassette Deck B door
27. FM 75 ohm antena terminal
27
28. AM/MW antenna socket
31
28
29. AUX IN jack
30. AC cord
29
31. Speaker terminals
30
RANDOM PLAY
This function will allow a single track or all the tracks on the disc to be played repeatedly.
1. Press the RANDOM button, the word
2. Press the
PLAY/PAUSE button to start
"RANDOM" will appear on the display.
play.
RANDOM
RANDOM
TO CANCEL RANDOM PLAYBACK
1. Press the
STOP button to stop random
2. Press the RANDOM button to deactivate ran-
playing.
dom playback.
RANDOM
INTRODUCTION PLAY - - at CD stop mode (for remote control only)
Press the SHIFT & INTRO button, the word "INTRO" will appear on the display.
INTRO
TO CANCEL INTRODUCTION PLAY
Press the STOP button to stop introduction play.
DISPLAY
1
2 3
4
5
6
7
8
9
10
11
TUNER
TIMER
12
MEMORY
13
1. X-BASS indicator
9. TUNER function Indicator
2. CD function indicator
10. INTRODUCTION indicator
3. BAND FM/MW(AM) indicator
11. TIMER ON/OFF indicators
4. REPEAT mode indicators
12. SLEEP indicator
5. PLAY / PAUSE indicators
13. CLOCK/CD TIMING/TAPE/AUX/TUNER FRE-
6. MEMORY indicator
QUENCY/CD TRACK/PRESET STATION
7. FM STEREO indicator
NUMBER indicators
8. CD RANDOM indicator
POWER INDICATOR
While the AC cord is connected and the unit is on stand-by, power will be consumed and only the
clock display will be lit.
• Press the POWER button to turn on the unit.
After a short period of time the display will show:
POWER ON
STANDBY
TUNER
• Press the TAPE button.
After a short period of time the display will show:
TAPE
• Press the CD button.
After a short period of time the display will show:
CD
• Press the AUX button (on remote control only).
After a short period of time the display will show:
• After using the unit press the POWER button until the display shows the time (at standby mode).
REPEAT PLAY
This function will allow a single track or all the tracks on the disc to be played repeatedly.
TO REPEAT THE SAME TRACK
TO REPEAT THE WHOLE DISC
Press the REPEAT button to repeat the cur-
Press the REPEAT button until the "REPEAT
rent track. The "REPEAT 1" indicator light up.
ALL" indicator light up.
PRESET/
PRESET/
TO CANCEL REPEAT PLAY
Press REPEAT button until the REPEAT indicator turn off.
PRESET/
DURING STOP MODE
DURING PAUSE MODE
The REPEAT operations can also be set in the
The REPEAT operations can also be set from
stop mode. The player will start playing from
paused playback point. The player will start play-
Track 1 of the currently selected disc after
ing again after
PLAY/PAUSE button is
PLAY/PAUSE button is pressed.
pressed.
TURNING ON THE UNIT
TO TURN ON THE UNIT
Press POWER button, the display will illuminate. Select the desired function and the corresponding
function indicator will show in the display.
TO TURN OFF THE UNIT
Press the POWER button to enter STANDBY. The display illumination will fade and only the clock
display will be shown.
CLOCK SETTING -
in standby mode
1. Press
MEMORY button the Hour and
2. Press
but-
SKIP/TUNING (
DOWN )
Minutes will flash.
ton to set hour.
SKIP/ TUNING
UP
MEMORY
DOWN
3. Press
SKIP/TUNING (
UP )
button to
4. Press
MEMORY button to set hour and
set minutes.
minutes, start the clock.
SKIP/ TUNING
UP
MEMORY
DOWN
Note: If a button is not pressed for 10 seconds the clock set mode will be exited automatically.
ADJUSTING THE SOUND
To adjust the volume
For loud deep bass
VOL
Press
button
to increase the
Press X-BASS button
volume.
to increased the low
frequency sound level.
Press
button
to decrease the
volume.
WHEN RECORDING
Adjustments to the VOLUME control or the X-BASS control will not affect the recording.
FOR PRIVATE LISTENING
Connect a headphone (ø3.5mm stereo mini-plug) to the PHONES jack.
When the headphone is connected, speakers are automatically disconnected.
PROGRAMMING PLAYBACK --- in the stop mode
Up to 20 tracks can be programmed to play in any order using this function.
1. Press
MEMORY button (in stop mode).
MEMORY
2. Press
SKIP
button to select the desired track.
SKIP/ TUNING
UP
DOWN
3. Press
MEMORY button again to store this track in memory.
MEMORY
4. To program additional tracks,
5. To start playback, press the
PLAY/PAUSE
button.
repeat step 2 to 3.
NOTE:
During programme playback, the
SKIP
buttons can only be used for the selected
t r a c k s .
TIMER OPERATION (for remote control only)
The power can be turned on and off automatically at a preset time so that you can wake up to tape
music, CD, radio or AUX. Make sure the clock is set the correct before the timer setting.
TIMER SETTING - at standby mode
1. Press MODE/REMAIN button until
ON/OFF is in the display.
2. Press MEM
button in clock mode. Hour and minutes will flash.
3. Press
TUN +
to set correct hour.
buttons
4. Press
TUN -
buttons
to set the correct minutes.
5. Press MEM
button to store the ON/OFF time. It will return to normal mode.
PLAY TIMER
RECORD TIMER
1. Set the time of the timer-on and timer-off.
The system will record a radio broadcast
2. Select the desired program source with
at a preset time.
the FUNCTION.
TUNER: Select a band and station.
1. Set the time of the timer-on and timer-off.
TAPE: Insert the cassette tape.
2. Set to TUNER.
CD: Insert a disc.
3. Select a band and station.
3. Press TIMER.
4. Insert the cassette tape for recording.
TIMER appears in the display.
5. Press TIMER.
4. Press POWER to standby mode.
TIMER appears in the display.
5. For cassette playback, press PLAY.
6. Press POWER to standby mode.
7. Press REC (record) which also engages
At the timer-on time, the system turns on
PLAY.
automatically.
Cancel the timer function
Press the SHIFT and TIMER button until the timer indicator turn off.
SLEEP SETTING (for remote control only)
When the sleep timer is used, the power is automatically turned off after the specified time passes.
1. Press the SLEEP button while the power
2. Press SLEEP button repeatedly to select
is on. "SLEEP 90" lights in the display.
the length of remaining time until the unit
Note: SLEEP time can only be adjust in
turns off.
TUNER, TAPE, CD and AUX modes.
It changes the indicator in the following way:
The sleep timer is set and the SLEEP indica-
tor lights in the display. Let go when required
sleep time (in minutes) is shown.
To cancel the sleep timer, press the SLEEP
button once and "SLEEP" will go out in the
display.
STOPPING AND CANCELLING PROGRAMMED PLAYBACK
To stop programmed play for a moment:
• Press the
PLAY/PAUSE button and "II" will be displayed.
Press this button again to resume playing.
MEMORY
To stop programed playback:
• Press the
STOP button.
To erase the whole programme:
or
Open the disc tray by pressing the OPEN/
• Press the
STOP button or select another
function.
CLOSE button.
OPEN/CLOSE

Advertisement

loading

Summary of Contents for Audiovox CE520

  • Page 1 SYSTEM CONNECTIONS PARTS IDENTIFICATION MW/AM LOOP ANTENNA The AC cord to an AC outlet SPEAKER CORD CONNECTION Connect the right speaker to the R terminal, and the left to the L terminal. Connect the wires with the printed white lines to the red (+) terminals and the plain-black wires to the black (-) terminals.
  • Page 2 TUNER SECTION TUNING INTO A STATION MANUALLY PRESETTING STATION The unit can store stations (FM 16 stations and AM 16 stations).They can be tuned in to by selecting 1. Press the TUNER button. their preset numbers. It is possible to store stations of any band in order of your choice. Manual memory presetting TUNER This function allows you to manually preset stations into any desired memory.
  • Page 3 RACCORDEMENT DE LA CHAÎNE IDENTIFICATION DES COMMANDES ANTENNE CADRE AM/MW Cordon CA à brancher dans une prise CA CONNEXION DES FILS D’ENCEINTES Raccordez l’enceinte droite à la borne R (droite) et l’enceinte gauche à la borne L (gauche). Raccordez les fils rouges aux bornes rouges (+) et les fils noirs aux bornes noires (-).
  • Page 4: Instructions De Fonctionnement

    SYNTONISATEUR SYNTONISATION MANUELLE D’UNE STATION PRÉRÉGLAGE DE STATIONS Vous pouvez mettre en mémoire 16 stations FM et 16 stations AM). Vous pouvez ensuite les syntoniser 1. Pressez la touche TUNER (syntonisateur). en choisissant leurs numéros de préréglage. Il est possible de mettre les stations en mémoire dans n’importe quel ordre et dans la bande de votre choix.
  • Page 5 CONEXIONES DEL SISTEMA CONEXIONES DEL SISTEMA CONEXIONES DEL SISTEMA CONEXIONES DEL SISTEMA CONEXIONES DEL SISTEMA IDENTIFICACIÓN DE LAS P IDENTIFICACIÓN DE LAS P IDENTIFICACIÓN DE LAS PAR IDENTIFICACIÓN DE LAS P IDENTIFICACIÓN DE LAS P ANTENA DE CUADRO AM/MW El cable de alimentación de CA se conecta al enchufe de CA ubicado en la pared.
  • Page 6: Instrucciones De Operación

    SECCIÓN DE LA RADIO PARA SINTONIZAR MANUALMENTE UNA ESTACIÓN PARA PROGRAMAR UNA ESTACIÓN Esta unidad puede almacenar hasta 16 estaciones en las bandas AM y FM. Para localizar dichas 1. Presione el botón TUNER. estaciones, usted deberá seleccionar el número de programación pertinente. Usted podrá almacenar en la memoria estaciones de cualquier banda y en el orden que usted desee.

This manual is also suitable for:

Ce520cd2271