Editing A Kit Or Instrument; Selecting Kits (Kit); Editing A Kit's Settings (Kit Edit); Detailed Reverb Settings - Roland TR-8S Owner's Manual

Editing a Kit or Instrument

Selecting Kits
(KIT)
Here's how to select kits.
1.
Press the [KIT] button to make it light.
The KIT screen appears.
If the kit is being edited, an
number.
2.
Use the [VALUE] knob to select a kit.
3.
Press the [KIT] button once again.
Exit the KIT screen.
Editing a Kit's Settings
Here's how to edit the settings of the currently selected kit.
* If you want to keep the edited kit settings, you must save the kit
(p. 18).
1.
Hold down the [SHIFT]
button.
The KIT Edit screen appears.
2.
Select a parameter.
2-1.
Use the [VALUE]
2-2.
Press the [ENTER]
Proceed to editing the parameter value (step 3).
3.
Modify values.
3-1.
[VALUE]
Use the
3-2.
Press the [ENTER]
Return to selecting a parameter (step 2).
4.
[KIT]
Press the button.
Exit the KIT Edit screen.
KIT Edit parameter
Category Explanation
LEVEL Level parameter
Edit the reverb settings.
REVERB
&

"Detailed Reverb Settings"

Edit the delay settings.
DELAY
&

"Detailed Delay Settings"

&
MASTER FX "Master Effect (MASTER FX)"
&
"Inputting an External Audio Source
EXT IN
(EXT IN)"
&
"Using the LFO to Modify a Parameter"
LFO
(p. 16)
Specifies the output destination of each
instrument.
OUTPUT
MIX, ASSIGN 1–6 (mono), ASSIGN A–C (stereo)
Specifies the mute setting of each instrument.
MUTE
Muting occurs when the specified instrument is
sounded.
Assigns a parameter to the
instrument edit section.
CTRL
&
"Assigning a Different Function for Each
Instrument to the [CTRL] Knob"
14
"*" is shown at the left side of the kit
(KIT Edit)
button and press the
knob to select a parameter.
button.
knob to edit the parameter value.
button.
(p. 14)
(p. 14)
(p. 15)
(p. 21)
[CTRL] knobs of the
(p. 15)
Category
COLOR
NAME
& For details, refer to
MEMO
5 When you switch kits, the position of the knobs might differ
from the values of the kit; for such cases, you can choose
whether knob movement changes the sound immediately or
only after the knob position matches or passes through the
value of the kit.
&
"UTILITY"
5 The parameters of the kit that you are editing are remembered
until you turn off the power. If you select a different kit and
then re-select the edited kit, it comes back in the edited state;
however, if you turn the power off and on again, the kit returns
to its state prior to editing. If you want to keep the edited kit
settings, you must save the kit.
&
"Saving the Pattern, Kit, or System Settings (WRITE)"
[KIT]
(p. 18)
Detailed Reverb Settings
In the KIT Edit screen, select REVERB.
Parameter
Type
Time
Level
Pre Delay
Low Cut
High Cut
Density
Detailed Delay Settings
In the KIT Edit screen, select DELAY.
Parameter
Type
TempoSync Synchronizes the delay time (Time) to the tempo.
Level
Time
Feedback
The editable parameters differ depending on the type of delay.
& For details, refer to
Explanation
Specifies the color of the level fader LEDs.
Rename the kit.
&
"Entering a Kit Name or Other Characters"
(p. 18)
"Reference Manual"
0 0
"GENERAL" "KnobMode"
Explanation
Type of reverb
Time length of reverberation
* You can control this by holding down the
[LEVEL]
and turning the REVERB
Output level of reverberation
[LEVEL]
* You can use the REVERB
Adjusts the delay time from the direct sound until
the reverb sound is heard.
Adjusts the frequency below which the low-
frequency content of the reverb will be reduced.
Adjusts the frequency above which the high-
frequency content of the reverb will be reduced.
Density of reverb
Explanation
Type of delay
Output level of delay sound
* You can use the DELAY [LEVEL]
Adjusts the delay time from the direct sound until
the delay sound is heard.
[TIME]
* You can use the DELAY knob to control this.
Adjusts the amount of delay feedback.
[FEEDBACK]
* You can use the DELAY
this.
"Reference Manual"
(PDF).
parameter
[KIT] button
knob.
knob to control this.
knob to control this.
knob to control
(PDF).