Advertisement
Quick Links
Advertisement
Related Manuals for Roland TR-6S
Summary of Contents for Roland TR-6S
- Page 1 Parameter Guide © 2020 Roland Corporation...
- Page 2 KIT Parameters Parameter Value Explanation DLY, PAN 630Hz, 800Hz, Parameter Value Explanation 1kHz, 1.25kHz, -INF, -53.0dB– 1.6kHz, 2kHz, Specifies the volume of the kit. Level Specifies the frequency above which the 0.0dB–+10.0dB 2.5kHz, 3.15kHz, high-frequency region of the delay sound HighCut 4kHz, 5kHz, is cut.
- Page 3 KIT Parameters KIT: MASTER FX Parameter Value Explanation Turn this ON if you want to prevent OFF, ON excessive volume from occurring when Clipper Parameter Value Explanation Resonance is raised. Selects the type of MASTER FX. HPF: high pass filter (cuts the low-frequency region) Specifies the cutoff frequency.
- Page 4 KIT Parameters Parameter Value Explanation Parameter Value Explanation Specifies the compression ratio. ISOLATOR 1: 1.00, 1: 1.12, 1: 1.25, 1: 1.40, 1: The higher the ratio, the more Adjusts the ISOLATOR effect. 1.60, 1: 1.80, 1: compression is applied to the sound when Balance OFF, 1–255 With a setting of 255, the ISOLATOR effect...
- Page 5 KIT Parameters Parameter Value Explanation Parameter Value Explanation Adjusts the distortion effect. Specifies the center frequency at which Balance the phase effect is applied. OFF, 1–255 With a setting of 255, the distortion effect Manual MASTER FX [CTRL] *1 0–255 is at 100%.
- Page 6 KIT Parameters KIT: CTRL Parameter Value Explanation Switches the range that can be adjusted by BandIntrvl. SBF1, SBF2, SBF3, Type Parameter Value Explanation SBF4, SBF5, SBF6 Switch the Type if you want to narrow the bands when adjusting BandIntrvl. Assigns a parameter to the [CTRL] knobs of widen) the instrument edit section so that it can -INF, -53.0dB–...
- Page 7 INST Parameters INST Parameter Value Explanation Specifies the playback direction and playback speed. Parameter Value Explanation +1.00: Play at the original speed. Common to all tones +0.99–+0.01: Play at a lower speed. -1.00–0.00–+1.00 Rate 0.00: Don’t play. Tune (steps of 0.01) -128–0–+127 Adjusts the tuning (pitch).
- Page 8 INST Parameters INST FX Parameter Value Explanation LPF/HPF Specifies the cutoff frequency. Parameter Value Explanation Lowering the Depth value (toward LPF) Selects the type of INST FX. applies an LPF effect, lowering the cutoff LPF 127–FLAT– Depth THRU No INST FX effect is applied. frequency.
- Page 9 INST Parameters Parameter Value Explanation Parameter Value Explanation Specifies the time from when the input Adjusts the compression effect. exceeds the level specified by Thre until OFF, 1–255 CmpBalance With a setting of 255, the compression the volume is compressed. effect is at 100%.
- Page 10 INST Parameters Parameter Value Explanation Parameter Value Explanation Specifies the high-frequency level of the Volume balance between the dry sound -INF, -53.0dB– OFF, 1–255 Balance EQ that is applied after distorting the and effect sound DrvPstH 0.0dB–+10.0dB sound. 0–255 Output Level Level CRUSHER FREQ SHIFT...
- Page 11 Start Kit * If KitSel is set to PTN, and a pattern Import Loads an audio file from the SD card into the TR-6S (import) whose PTN SETTING parameter KIT Sw is ON is specified as the Start Ptn, the Start Deletes a loaded user sample.
- Page 12 SYSTEM Parameters / UTILITY Menu SYNC/TEMPO Parameter Value Explanation Specifies whether changes to the kit settings (panel operations) are transmitted OFF, ON Tx EditData Parameter Value Explanation as MIDI messages (ON) or are not transmitted (OFF). Specifies the tempo source. AUTO: If MIDI clock is input from the MIDI Specifies whether MIDI Clock messages...
- Page 13 TR-6S Audio Diagram :EXT IN Delay Send INST DELAY Delay Send BD - OH :DELAY Reverb Send :EXT IN Reverb Send REVERB INST Reverb Send BD - OH : EXT IN : EXT IN Gain VOLUME USB EXT IN SIDE CHAIN...