S S E E T T T T I I N N G G U U P P T T H H E E U U R R C C - - 9 9 0 0 4 4 0 0; How To Set Up The Urc-9040 To Control Your Pc - One for All URC-9040 Instruction Manual

H H o o w w t t o o s s e e t t u u p p t t h h e e U U R R C C - - 9 9 0 0 4 4 0 0 t t o o c c o o n n t t r r o o l l y y o o u u r r P P C C
The URC-9040 PC Media Remote with OFA Media Centre allows you to control your
digital content and access it on your PC or on your home entertainment system,
via the Command Center. The Command Center connects to your PC by a USB
cable.
N N O O T T E E : : - - The antenna of the RF receiver should be placed in the upright position!
- This product is not intended to be used with any USB extension cable!
T T o o s s e e t t u u p p y y o o u u r r C C o o m m m m a a n n d d C C e e n n t t r r e e w w i i t t h h y y o o u u r r P P C C a a n n d d i i n n s s t t a a l l l l t t h h e e O O F F A A P P C C M M e e d d i i a a C C e e n n t t r r e e
a a p p p p l l i i c c a a t t i i o o n n , , s s i i m m p p l l y y i i n n s s e e r r t t t t h h e e s s e e t t u u p p C C D D s s u u p p p p l l i i e e d d i i n n t t h h e e p p a a c c k k a a g g e e i i n n t t o o y y o o u u r r P P C C , ,
s s e e l l e e c c t t t t h h e e l l a a n n g g u u a a g g e e , , a a n n d d f f o o l l l l o o w w t t h h e e o o n n s s c c r r e e e e n n i i n n s s t t r r u u c c t t i i o o n n s s . .
I I M M P P O O R R T T A A N N T T : : You do not need to program a device code into the URC-9040 PC Media Remote
with OFA Media Centre to control the Command Center. However, it is possible
that someone else in your building or complex may also have a URC-9040
Media Remote with OFA Media Centre. Therefore so the URC-9040 remote contains
3 different addresses for the Command Center, which you can cycle between
to avoid conflicting signals.
N N O O T T E E : : If more than 10 seconds pass between key presses, the URC-9040 remote
exits programming.
To change the Command Center address:
1 1 . .
2 2 . .
3 3 . .
>
or
>
or
N N O O T T E E : : If the power key displays a long blink, the entry is invalid. Repeat steps 1 through 3.
N N O O T T E E : : You must also change the address on the O O F F A A M M e e d d i i a a C C e e n n t t r r e e application to match the address
setup on your URC-9040.
Note the PC address being used below:
6

S S e e t t t t i i n n g g u u p p t t h h e e U U R R C C - - 9 9 0 0 4 4 0 0

Press P P C C .
P P r r e e s s s s a a n n d d h h o o l l d d d d o o w w n n R R E E W W I I N N D D + + F F A A S S T T F F O O R R W W A A R R D D
s s i i m m u u l l t t a a n n e e o o u u s s l l y y u u n n t t i i l l t t h h e e U U R R C C - - 9 9 0 0 4 4 0 0 ' ' s s L L E E D D ( ( r r e e d d l l i i g g h h t t ) ) b b l l i i n n k k s s t t w w i i c c e e
(the LED will blink once and then twice).
Press 4 4 1 1 ( ( a a d d d d r r e e s s s s 1 1 ) ) , 4 4 2 2 ( ( a a d d d d r r e e s s s s 2 2 ) ) , or 4 4 3 3 ( ( a a d d d d r r e e s s s s 3 3 ) ) to change
the address. The LED will light up twice.
WWW.ONEFORALL.COM