Cleaning And Maintenance; Lubrication (Fig. F-4); Belt And Running Deck; General Cleaning - Tunturi T80 User Manual

The warranty does not cover sounds or noises emitted
during use where these do not substantially impede the
use of the equipment and where they are not caused by
a fault in the equipment.
The warranty does not cover defects arising from the
failure to carry periodic maintenance as outlined within
the Owner's Manual for the product. Furthermore, the
warranty does not cover defects arising from usage and
storage within an unsuitable environment as described
within the Owner's Manual which should be indoors,
dry, dust and grit free and within a temperature range
of +15°C to +35°C. The warranty does not cover
maintenance activities, such as cleaning, lubricating,
and normal part adjustments, nor installation
procedures that customers can accomplish themselves,
such as changing uncomplicated meters, pedals and
other similar parts not requiring any dismantling/
reassembling of the fitness equipment. Warranty
repairs carried out by other than authorised Tunturi
representatives are not covered.
Failure to follow the instructions given in the Owner's
Manual will invalidate the product's warranty.

Cleaning and maintenance

WARNING
• Before cleaning and maintenance, remove the
mains plug from the wall socket.
• Do not use solvents to clean the equipment.
- Do not block the ventilation openings. Keep the
ventilation openings clear from dust, dirt and other
obstructions.
- Clean the equipment with a soft, absorbent cloth
after each use.
- Clean the visible parts of the equipment with a
vacuum cleaner with a small suction nozzle
- Regularly check that all screws and nuts are tight.

Belt and Running Deck

Your treadmill uses a very high-efficient low-friction
bed. Performance is maximized when the running deck
is kept as clean as possible. Use a soft, damp cloth or
paper towel to wipe the edge of the belt and the area
between the belt edge and frame. Also reach as far as
practical directly under the belt edge. This should be
done once a month to extend belt and running deck
life. Use water only - no cleaners or abrasives. A mild
soap and water solution along with a nylon scrub brush
will clean the top of the textured belt. Allow the belt to
dry before using.

Lubrication (Fig. F-4)

The running belt must be checked for lubrication once
per 2 months, based on the average use of 60 minutes
per day.
WARNING
• Before lubrication, remove the mains plug from
the wall socket.
CAUTION
• Only lubricate the running belt if necessary. If
you apply too much lubricant, the running belt
will slip easily due to lack of friction.
- Stand steadily on the running belt.
- Take hold of the front handlebar and push the
running belt with your feet so that it slides back and
forth. The running belt must move smoothly and
evenly without making sound.
- If the running belt does not move smoothly and
evenly or if the running belt does not move at all,
touch the underside of the running belt with your
fingertips to check the lubrication:
• If you feel lubrication or your fingertips are shiny,
there is sufficient lubrication on the running belt.
• If you do not feel lubrication or your fingertips
are dusty or rough, apply lubricant (15-20 ml)
in the middle of the running deck under the
running belt and let the equipment operate at
5km/h for at least 5 minutes.
• After lubrication, do not fold the equipment
before having done a workout for 20 minutes
with a speed of at least 5 km/h. The lubricant will
be spread evenly over the running belt.
Belt Dust
This occurs during normal break-in or until the belt
stabilizes. Wiping excess off with a damp cloth will
minimize build-up.

General Cleaning

Dirt, dust, and pet hair can block air inlets and
accumulate on the running belt. On a monthly basis:
vacuum underneath your treadmill to prevent buildup.
Twice a year, you should remove the black motor hood
and vacuum out dirt that may accumulate.
UNPLUG POWER CORD BEFORE THIS TASK.

Belt adjustments

Adjustment must be made from the rear roller. The
adjustment bolts are located at the end of the step rails
in the end caps.
- Tighten the rear roller bolts (clockwise) only enough
to prevent slippage at the front roller. Turn both
running belt tension adjustment bolts in increments
of 1/4 turn each and inspect for proper tension by
3 5
English