Axis 214 PTZ User Manual page 2

About this Document
This manual is intended for administrators and users of the
AXIS 214 PTZ PTZ Network Camera, and is applicable for
software release 4.30. Previous experience of networking will
be of use when installing and using this product. Some
knowledge of UNIX or Linux-based systems may also be
beneficial, for developing shell scripts and applications. Later
versions of this document will be posted to the Axis Website,
as required.
Safety Notices Used In This Manual
Caution! - Indicates a potential hazard that can damage the
product.
Important! - Indicates a hazard that can seriously impair
operation.
Do not proceed beyond any of the above notices until you
have fully understood the implications.
Intellectual Property Rights
Axis AB has intellectual property rights relating to
technology embodied in the product described in this
document. In particular, and without limitation, these
intellectual property rights may include one or more of the
patents listed at http://www.axis.com/patent.htm and one or
more additional patents or pending patent applications in the
US and other countries.
This product contains licensed third-party software. See the
menu item "About" in the product's user interface for more
information.
This product contains source code copyright Apple Computer,
Inc., under the terms of Apple Public Source License 2.0 (see
http://www.opensource.apple.com/apsl/).
The source code is available from:
http://developer.apple.com/darwin/projects/bonjour/
Legal Considerations
Video surveillance can be prohibited by laws that vary from
country to country. Check the laws in your local region
before using this product for surveillance purposes.
Electromagnetic Compatibility (EMC)
If use of this equipment causes harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures: Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a different circuit to
the receiver. Consult your dealer or an experienced radio/TV
technician for help. Shielded (STP) network cables must be
used with this unit to ensure compliance with EMC standards.
USA -
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause interference, in which case the user will
be required to correct the interference at his own expense.
Canada -
This Class A digital apparatus complies with
Canadian ICES-003.
Europe -
This digital equipment fulfills the
requirements for radiated emission according to limit A of
EN55022/1998, and the requirements for immunity according
to EN55024/1998 residential, commercial, and industry.
Warning! This is a Class A product. In a domestic
environment this product may cause radio interference, in
AXIS COMMUNICATIONS
<Product Name> Quick User's Guide
which case the user may be required to take adequate measures.
Japan -
This is a class A product based on the standard of the
Voluntary Control Council for Interference by Information
Technology Equipment (VCCI). If this equipment is used in a
domestic environment, radio disturbance may arise. When such
trouble occurs, the user may be required to take corrective action.
Australia -
This electronic device meets the requirements of the
Radio communications (Electromagnetic Compatibility) Standard
1998 AS/NZS 3548.
Warning! This is a Class A product. In a domestic environment
this product may cause radio interference, in which case the user
may be required to take adequate measures.
Liability
Every care has been taken in the preparation of this manual.
Please inform your local Axis office of any inaccuracies or
omissions. Axis Communications AB cannot be held responsible
for any technical or typographical errors and reserves the right to
make changes to the product and manuals without prior notice.
Axis Communications AB makes no warranty of any kind with
regard to the material contained within this document, including,
but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. Axis Communications AB shall
not be liable nor responsible for incidental or consequential
damages in connection with the furnishing, performance or use of
this material.
Trademark Acknowledgments
Ethernet, Internet Explorer, Linux, Microsoft, Mozilla, OS/2,
UNIX, Wfine, Windows, WWW are registered trademarks of the
respective holders. Java and all Java-based trademarks and logos
are trademarks or registered trademarks of Sun Microsystems, Inc.
in the United States and other countries. Axis Communications
AB is independent of Sun Microsystems Inc. UPnP
certification mark of the UPnP
Bonjour is a trademark of Apple Computer Inc.
Support
Should you require any technical assistance, please contact your
Axis reseller. If your questions cannot be answered immediately,
your reseller will forward your queries through the appropriate
channels to ensure a rapid response. If you are connected to the
Internet, you can:
• download user documentation and firmware updates
• find answers to resolved problems in the FAQ database. Search
by product, category, or phrases
• report problems to Axis support by logging in to your private
support area
• visit Axis Support at www.axis.com/techsup/
Safety Notice - Battery Replacement
The AXIS 214 PTZ uses a 3.0V CR2032 Lithium battery as the
power supply for its internal real-time clock (RTC). Under normal
conditions this battery will last for a minimum of 5 years. Low
battery power affects the operation of the RTC, causing it to reset
at every power-up. A log message will appear when the battery
needs replacing. The battery should not be replaced unless
required!
If the battery does need replacing, please observe the following:
• Danger of Explosion if battery is incorrectly replaced
• Replace only with the same or equivalent battery, as
recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer's
instructions.
AXIS 214 PTZ User's Manual
Revision 1.0
Part No: 25353r7
August 2006
Copyright© Axis Communications AB, 2005-2006
TM
is a
TM
Implementers Corporation.